A Whirlpool washing machine that’s not working correctly can be frustrating particularly if the cycle isn’t able to go through. It is possible to be left with wet clothes which need to be dried. You can reduce time and cost by understanding the reasons for the washing machine not going on to the next cycle. We’ll discuss the most typical reasons why your Whirlpool washing machines might not move into the next cycle, and provide some suggestions on how to return it to normal operation.
The kind of washer you are using will determine the reason a Whirlpool washer can’t go into the next cycle.
If the lid switch on top load Whirlpool washer is damaged and the washer is not able to proceed to spin or drain cycle. Whirlpool washers that fail to complete the cycle could have a malfunctioning timer or water-level pressure switches that are not working properly.
A defective shifter assembly or a malfunctioning drain pump can cause a vertical modular top load (VMW), washer to shut down mid-cycle. The washer could also stop mid-cycle when there is excessive suds.
A front-loader can be prevented from running a cycle when it is damaged by a door lock or the main electronic control board malfunction, or a motor control board issue. If the washer is aware of an issue, this kind of Whirlpool washer sends an error message in digital format to the computer. The cycle will stop.
These repairs could help you solve the Whirlpool washer issue.
Replace the Whirlpool lid on the washer
Top-load Whirlpool lid switch on the washer is an emergency switch that is used to determine whether the lid is shut. If the basket spins the lid has to be shut. The washer won’t drain or spin when it detects the lid is open.
Top-load washers must ensure that the Whirlpool lid of the washer is shut before the motor for the washer is able to run. Top-load washers with an open lid aren’t capable of filling.
Replace the switch in the event that the lid switch isn’t able to detect whether the lid is shut.
Replace the Whirlpool washer-shifter assembly
On the bottom of the washer is the shifter assembly, which is called the actuator-in-a-top-load washer. The motor inside the shifter assembly moves the drive system from the spin mode to the agitation mode. The location of the drive system is tracked by a sensor mounted within the shifter. The washer will stop when the motor, sensor or mechanical components of the shifter assembly fail, and will send an error message. If the Whirlpool Shifter Assembly fails Replace it.
Change the Whirlpool washer lock assembly
Whirlpool’s front-load washer lock assembly has a security switch that detects if the door to the washer has been closed , as well as an latch. The door won’t close in the event that any of these components fail when the door is opened. If one of the components fails when the door is closed, it will not be able to open. If any component is damaged, you should replace the entire assembly.
Change the control board of your Whirlpool washer
The primary Whirlpool electronic controller board, sometimes referred to as the mother board or mother board, is responsible for the timing and execution of washer components. It regulates the drain valves and fill valves pumps, and also the drive motor.
The Whirlpool washer timer needs to be replaced
The Whirlpool washing machine’s timer, also referred to as a cycle selector, is the dial that is used to set the timer. The timer regulates the Whirlpool washing machine’s cycle, from the initial filling to the final spin. If the timer isn’t moving the washer throughout its cycle, you can replace it.
Whirlpool washer drain pump may be replaced or repaired
The Whirlpool drain pumps draw the water from washing machines at the appropriate timings during washing cycles. The pump’s bearing may wear out, or the seal could fail. A belt-driven pump could fail, the seal could fail, or the pulley could be able to shear. A malfunctioning pump could produce a sound in the event that the washer gets filled. Repairing the pump is possible in certain cases by removing the debris out of it or replacing a seal or fixing wiring issues. It is possible to replace the pump in cases where it’s impossible to repair or rebuild it.
Change the Whirlpool washer motor controller board
Whirlpool’s motor control panel is also known as the circuit-control board is found in front-load washers. It’s usually located at the washer’s bottom, next to the drive motor. It regulates the speed of the drive motor as well as the direction it’s directed to for spinning and tumble movements. The motor control board could require replacement in the event that the motor ceases to run.
Change the Whirlpool washer water level pressure switch
The Whirlpool water level pressure switch is used to measure the level of water inside the washer. The washer won’t fill properly if the water level pressure sensor has been damaged. It might not fill correctly or overfill until it spills over. Change the pressure switch if it fails to detect and regulate the water levels within the Whirlpool washer.
A washing machine from Whirlpool that isn’t going to the next cycle can be a frustrating issue. It could also cause disruption to the routine of washing clothes. Knowing the causes and solutions will aid in identifying the issue and bring back normal operation to your washer. Finding the root of the issue regardless of whether it’s an easy fix like the blockage of a drain or more complicated problems with the control board will help you save time and cost. It’s possible to begin fixing your Whirlpool washing machine’s issues with cycle advancing by following these suggestions and suggestions.