A malfunctioning Hotpoint washing machine could be quite a hassle when it fails to move on to the next cycle. You may get wet clothes which need to be dried. It is possible to reduce time and cost by understanding the reason for the washing machine that isn’t moving to the next cycle. In this article, we will examine some common reasons why your Hotpoint washing machine may be stuck in a cycle . Additionally, we will offer some troubleshooting suggestions to assist you in getting the machine back to normal functioning.
The type of washer that you are using will determine the reason a Hotpoint washer can’t go into the next cycle.
If the lid switch for a top load Hotpoint washer is broken and the washer is not able to advance to the drain or spin cycle. A Hotpoint washing machine that isn’t able to finish the cycle could also be suffering from a malfunctioning timer or malfunctioning pressure switch for the water level.
In the other hand, if you have a vertical modular (VMW) top-load washer the shifter assembly that is defective or a failed drain pump could cause the washer in mid-cycle. This washer can also stop mid-cycle in the event that it has excessive suds.
For a front-loader the door of the washer may be damaged. A broken lock assembly, a failed main control board, or an inoperable motor control board may hinder the washing machine from completing the cycle. If the washer discovers an issue, this kind of Hotpoint washer sends an error code in digital format to the computer. The cycle will stop.
These repairs could solve the Hotpoint washer’s problem.
Replace the Hotpoint washer lid switch
The lid switch in top-load Hotpoint washer is a safety switch that checks whether the lid of the washer is closed. If the basket spins the lid must be closed. The dishwasher will not spin or drain in the event that it perceives the lid as open.
Top-load washers must ensure that the Hotpoint lid is sealed prior to the washer drive motor is able to run. Top-load washers that have an open lid are not suitable for filling.
If the switch for the lid isn’t sensing whether the lid is closed, replace the switch.
Replace the Hotpoint washer-shifter assembly
It is located on the bottom. the shifter assembly called the actuator-in-a-top-load washer. The motor of the shifter assembly shifts the drive system’s settings between spin and agitation mode. The position of the drive system is tracked through a sensor that is mounted within the shifter. The washer will stop washing if the motor, sensor or mechanical components of the shifter assembly fail and send an error code. Replace the Hotpoint shifter assembly in the event that it malfunctions.
Change the Hotpoint washer lock assembly
Hotpoint’s front-load washer lock assembly includes a safety switch that detects if the door of the washer is closed , as well as an latch. If any of these components fails when the door is open, the door will not be locked; if a part fails when the door is shut, the door won’t open. If one component is damaged, you should replace the entire assembly.
Replace the Hotpoint main control board for the washing machine
The primary Hotpoint electronic control board, also known as the Mother Board, governs the execution and timing of the washer’s component functions. It controls the fill valves as well as the drive motor, and the drain pump.
The Hotpoint washer timer should be replaced
The Hotpoint washing machine’s timer, also known as a cycle selector, is the dial is used to set the speed of your cycle. The timer is the one that controls the Hotpoint washer’s cycle from filling up to final spin. If the timer does not move the washer throughout its cycle, you can replace it.
Replace or repair or replace the Hotpoint washer drain pump
The Hotpoint drain pump draws water from the washing machine at appropriate times during the washing cycle. The pump’s bearing could wear down, or the seal could fail. A belt-driven pump can fail, and the seal may fail, and the pulley might be able to shear. A failing pump can produce a sound when the washer is full. Repairing the pump is possible in certain instances by clearing debris off it or replacing a seal or fixing wiring issues. You can also replace the pump when it’s not possible to repair or rebuild it.
Replace the Hotpoint motor control board for the washer.
Hotpoint’s motor control board, also known as the circuit-control board is located in front-load washers. It’s normally located at the washer’s bottom next to the drive motor. It is responsible for monitoring and controlling the drive motor speed and direction for the spin and tumble activities during the cycle. If the motor does not run the motor control board might need to be replaced.
Replace the Hotpoint washer water-level pressure switch
The Hotpoint water-level pressure switch detects the level of the water in the wash tub. If the water-level pressure switch is defective, the washer isn’t able to fill correctly. It may not fill completely or overfill, even to the point of overflowing. Change the pressure switch if it doesn’t detect and regulate the water levels within the Hotpoint washer.
A Hotpoint washer that stops getting ready for the next cycle is a bothersome issue. It may also interrupt the laundry routine. Recognizing the potential causes and the solutions can help you pinpoint the issue and get back to normal operation for the washing machine. It doesn’t matter if it’s a simple fix like a clogged drain or a more complex issue with the control board solving the problem can save you time and money in the long-term. It’s possible to begin fixing your Hotpoint washer’s problems with the cycle by following these tips and advice.