A Hoover washing machine that’s not working properly can cause frustration particularly if the cycle does not go through. The issue could result in a pile of wet clothes that are desperately in need of cleaning. Knowing the causes the reason your washer won’t advance to the next cycle could help you save both time and money by preventing unnecessary repairs or replacements. Here we will look at some common reasons your Hoover washing machines might not advance to the next cycle and offer some tips on how to bring it back in normal operation.
The type of washer that you own will determine why your Hoover washer can’t go to the next cycle.
A top-load Hoover washer can’t move to the spin cycle or drain because a defective lid switch causes the timer to think the washer lid is shut. Hoover washers that do not complete the cycle may be having a problem with a timer that isn’t working or damaged pressure switches on the water level.
A failed shifter assembly or a malfunctioning drain pump could cause vertical modular top load (VMW), washer to stop mid-cycle. In addition, excessive suds could cause this washer to stop working before the cycle is complete.
For a front-loader the door of the washer may be damaged. A broken lock assembly, failed main electronic control board, or an inoperable motor control board may stop the washer from completing a cycle. This model of Hoover washer often signals an error code digitally when the control for the washer detects an issue and stop the cycle.
These repairs could solve the Hoover washer issue.
Replace the Hoover lid on the washer
The lid switch on the top loader of a Hoover washer is a safety switch that checks whether the lid of the washer is shut. The lid must be closed in the event that the basket spins. in the event that the washer misinterprets that the lid has been opened it will not spin or drain after the wash cycle.
Top-load washers require that the Hoover lid on the washer be closed before the motor for the washer can run. Top-load washers with an open lid are not equipped to fill.
If the switch for the lid won’t be able to detect whether the lid is shut Replace the switch.
Install the Hoover washer shifter assembly
It is located on the bottom. the shifter assembly, which is called the actuator-in-a-top-load washer. The motor of the shifter assembly changes the drive system from spin mode to the agitation mode. The direction of the drive system is tracked through a sensor that is mounted within the shifter. The washer stops if the motor, sensor or mechanical components of its shifter assembly fail and emit an error message. If the Hoover Shifter Assembly is malfunctioning Replace it.
Replace the Hoover washer lock assembly
Hoover’s front-load washer lock includes a security switch to detect whether the door to the washer has been closed , as well as a latch. If any of these parts fails while the door is open, the door will not close; however, if one of the components fails while the door is shut, the door will not open. If one component is damaged, you should replace the whole assembly.
Replace the Hoover washer main control board
The main Hoover electronic control board, sometimes referred to as the Mother Board, controls the execution and timing of washer’s component functions. It regulates the fill valves and drain pumps as well as the drive motor.
Change the Hoover washer timer
The Hoover washing machine’s timing, also known as a cycle selector, is the dial that is used to set the speed of your cycle. The timer controls the Hoover washer’s cycle from initial filling all the way to the last spin. Replace the timer if it doesn’t allow the washer to progress through its cycles.
Hoover washer drain pump may be replaced or repaired
The Hoover drain pumps are used to remove the water from washing machines at the right timings during washing cycles. The pump’s bearing could seize, the seal can fail, or the impeller blades may break. The belt that drives belt-driven pump may break and the pulley may break off. A damaged pump may cause a hum in the event that the washer gets filled. You can repair the pump in certain situations by clearing debris from it and replacing the seal or fixing wiring issues. If the pump is unable to be repaired or rebuilt, you must replace it.
Replace the Hoover washer motor control board
Hoover’s motor control often referred to as the circuit-control board is situated in front-load washers. It’s normally located in the bottom of washers, next to the drive motor. It controls the speed of the drive motor , as well as the direction it’s directed for the action of the tumble and spin. The motor control board could need to be replaced when the motor stops working.
Replace the Hoover washer water pressure switch
The Hoover water level pressure switch measures the level of water inside the washer. The washer may not fill correctly if the water-level pressure sensor is damaged. It may not fill properly or overfill to the point of overflowing. If the pressure switch isn’t able to accurately determine and control the water level inside the Hoover washer, replace it.
A Hoover washing machine that has stopped getting ready for the next cycle is a bothersome issue. It can also interrupt your laundry routine. However, understanding the potential reasons for this issue can help you determine the cause and get your machine back to normal operation. The process of identifying the problem no matter if it’s a simple fix such as the blockage of a drain or more intricate problems with the control board will save you time and cost. It’s possible to begin fixing your Hoover washer’s problems with the cycle by following these tips and advice.