A Bosch washing-machine that isn’t working properly can cause frustration particularly if the cycle isn’t able to go through. There’s a chance that you’ll be left with wet clothes that need to be cleaned. Finding out the probable causes why your washing machine won’t go on into the next cycle could help you save both time and money by preventing unnecessary repairs or replacements. In this article, we will explore some of the common reasons why your Bosch washing machine is stuck in a cycle and give some troubleshooting advice to assist you in getting your machine back to normal operation.
The type of washer that you are using will determine the reason a Bosch washer isn’t able to move into the next cycle.
If the lid switch on a top load Bosch washer is damaged and the washer is not able to advance to the spin or drain cycle. Bosch washers that fail to complete the cycle could be suffering from a malfunctioning timing device or defective pressure switches for water levels.
A defective shifter assembly or a failing drain pump could cause vertical modular top load (VMW), washer to stop mid-cycle. The excessive amount of suds can cause this type of washer to stop before the cycle finishes.
If you have a front-loader washer, a broken washer door lock assembly, failed main electronic control board, or malfunctioning motor control board could hinder the washing machine from completing a cycle. This model of Bosch washer usually emits an error message in digital form when the washer control detects an issue and stops the cycle.
These Fixes Could Help You Solve Your Bosch Washer Problem
Replace the Bosch lid switch on the washer
Top-load Bosch washer’s lid switch a safety switch that determines whether the lid is shut. If the basket spins, the lid has to be shut. The dishwasher will not drain or spin in the event that it perceives the lid as open.
Some top-load models require that the Bosch washer lid be closed prior to the motor that drives the washer starts. The lid is not closed, which prevents certain top-load washers from filling.
Replace the switch if your lid switch doesn’t detect if the lid is closed.
Install the Bosch washer shifter assembly
The shifter, sometimes referred to as the actuator-in-a-top-load washer is mounted on the bottom of the gear case. The motor in the shifter shifts the drive system’s direction between spin and agitation mode. The direction of the drive system is monitored by a sensor mounted within the shifter. The washer will stop if the sensor, motor or mechanical components of the shifter assembly fail and send an error code. If the Bosch Shifter Assembly fails to function you should replace it.
Replace the Bosch washer door lock assembly
The Bosch door lock assembly that comes with the front-load washer has a safety switch that can detect whether the door of the washer is closed along with a latch and locking mechanism. If one of these components fails when the door is open, the door will not lock; if a component fails when the door is closed, the door won’t open. If any component fails, replace the whole assembly.
Replace the main control board that controls your Bosch washer
The primary Bosch electronic controller board, also known as the mother board, or the mother board, regulates the timing and execution of washer functions. It regulates the fill valves as well as the drive motor as well as the drain pump.
The Bosch washer timer should be replaced
The timer, sometimes called a cycle selectoris the dial you can use to control the timer on the Bosch washing machine equipped with mechanical controls. The timer is the one that controls the Bosch washer’s cycle from initial filling to the final spin. If the timer isn’t moving the washer through its cycles then replace it.
Bosch washer drain pump may be repaired or replaced
The Bosch drain pumps draw water from washers at appropriate timings during wash cycles. The bearing on the pump could wear down, or the seal could fail. A belt-driven pump can fail, the seal can fail, or the pulley can be able to shear. A humming sound when the washer is filled with water is an indication of a malfunctioning pump. In certain instances, you can repair the pump by cleaning the debris out replacing wiring malfunctions, or replacing the seal. If the pump can’t be repaired or rebuilt in any way, replace it.
Replace the Bosch washer motor controller board
The Bosch motor control board is a control circuit board found in front-load washers that is typically in the lowest part of the washer next to the drive motor. It controls the speed of the motor that drives it and the direction it is directed to for spinning and tumble movements. If the motor does not run it’s possible that the motor control board could need to be replaced.
Change the Bosch washer water-level pressure switch
The Bosch water-level pressure switch is a device that detects the level of the water in the tub for washing. If the pressure switch for water level is damaged, the washer isn’t filled properly. It might not fill at all or it could overfill even until it overflows. Replace the pressure switch if it doesn’t detect and regulate the water levels in the Bosch washer.
In conclusion, a Bosch washing machine that doesn’t progress into the next cycle can be a difficult issue that causes disruption to your laundry routine. Knowing the causes and the solutions can aid in identifying the issue and bring back normal operation to your washing machine. No matter what the cause is such as a clogged hose, or a more complicated problem with the control board solving the problem can help you save time and money in the long run. When you follow the steps and advice in this post, you can take the first step towards resolving the issue with your Bosch washing machine’s cycle speeding issues and help get your laundry back on track.