Many households need an efficient Insignia refrigerator that can offer plenty of Ice. If you require an ice maker for your drinks, to keep food in good condition, or even for entertaining guests, an efficient Ice maker is an essential. However, Insignia fridges that stop producing ice can become annoying and uninspiring. It is possible that an Insignia refrigerator may not produce ice due to various reasons, such as an obstruction in the water line, or a defective ice maker. This article will discuss the main causes of the ice maker’s failure, and provide steps for fixing it. The advice and information will allow you to identify the problem quickly and fix your refrigerator to create Ice again.
Common solutions to: My Insignia Refrigerator won’t make Ice
Insignia Refrigerator Main Board : The control board in the Insignia refrigerator regulates the voltage sent to its Ice maker. The ice maker may not work when the control board has been damaged. Check the board for any signs that indicate damage or a malfunctioning component. A multimeter can be used to verify that voltage is reaching the ice maker. Freezer Temperature is Above 10 Degrees F (-12C) If the freezer temperature is higher than 10 degrees Fahrenheit (-12C) and the ice maker will not produce ice cubes efficiently. The ice maker should operate at a temperature between 0 and 5°F (-18 to 15C). The temperature of the freezer shouldn’t be too hot. Also, make sure that the condenser fans are working correctly and that there’s no dust on the condenser coils. You should also check for frost accumulation on the coils of the condenser. If the tubes of the evaporator are frozen, it is likely that part of the defrost mechanism has failed.
Insignia Refrigerator Water Inlet Valve: The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. If the valve for water is damaged, or it has too little pressure the water will not flow through. This means that the Insignia Insignia Icemaker will not produce the ice. To work properly, the valve needs to be at or above 20psi. Check that the water pressure at the valve isn’t less than 20 psi. If the water pressure is adequate, utilize a multimeter to test for power to the valve that supplies water to. If the valve for water supply is supplying sufficient power and pressure, but the icemaker won’t make ice due to the lack of water, it must be replaced.
Insignia Refrigerator Ice Maker Assembly: One component might be damaged. Since many of the components for ice makers aren’t sold separately, you may need to purchase and replace the entire Insignia ice maker assembly. When installing the ice maker, check the water inlet valve, water line and the fan. Replace the icemaker assembly if none of these parts is damaged and the temperature of the freezer is not less than 15°F. Low Water Pressure from House Supply The house might not have enough water pressure. The valve that supplies water to the inlet pipe provides water to the ice and water dispenser. The valves for water inlet must function at minimum 20 psi. It is possible to test the flow of water and find out the pressure by conducting a test.
Confirm that the Insignia Icemaker is on: Make sure the Insignia Icemaker is on and the paddle or arm is able to move freely. If you have a model that is in the door and dispenses ice, ensure that the indicators stay in place while the door is open. Insignia Refrigerator Door Control: When the door of the Insignia refrigerator is opened the door switch turns off the water and ice dispensers. If the door switch is not working the dispenser won’t turn on. It is possible to test the continuity of your door switch with a multimeter. Replace it if you find that the door switch doesn’t have continuity when it is activated.
Insignia Refrigerator Icing Level Control Board: Some Insignia refrigerators utilize an infrared beam to detect the level of the bucket of ice. The infrared beam will be interrupted when the ice layer is at the top. The control board then shuts off the machine. When the ice level drops below the beam, the control board signals the ice maker to make more ice. The ice maker stops making ice when the ice level control board is down. Make sure that the power is available to the ice control board. If the ice level control board is getting power, but the ice maker won’t function, you must replace the control board for the ice level.
Insignia Refrigerator water filter: Clogged water filters can cause an obstruction in the flow of water to the dispenser, which can make it impossible for the maker to function properly. To ensure that water flow is maintained and quality, the filter should be changed about every six months.
Insignia Refrigerator Auger motor: An auger engine is needed to properly dispense ice in many Insignia refrigerators. The blade spins and pushes the frozen ice out of its container. The auger motor can fail and cause the ice to stop moving and falling into the chute. This could give the impression that the ice maker is not working. If the auger motor is not functioning, remove the bucket of ice and turn manually the bucket. Utilize a multimeter to determine if the auger turns freely. If the motor isn’t working or has no power, replace it.
Insignia Refrigerator Ice Bucket: On many Insignia refrigerators, the ice bucket uses a separate auger motor to spin an auger blade to move the frozen ice from the bucket down the chute of the dispenser. If the motor of the auger is spinning but the ice isn’t dispensing, the ice container could be damaged. If you notice cracks or wear, inspect the auger motor, ice bucket and drive coupler. If necessary change the ice bucket.
In conclusion, a Insignia refrigerator that isn’t producing ice is a typical issue that is caused by a range of factors. There are a variety of solutions to help your appliance produce ice again. Follow the instructions in this article to diagnose the issue and fix it with no professional assistance. Regular maintenance can help to prevent future issues. This includes cleaning the ice maker, and ensuring that the water line is clear. Do not hesitate to contact Insignia when you require ice.