A solid Danby refrigerator with plenty of ice is a must-have for all households. An ice maker that is functional is an essential appliance that makes Ice for any occasion. If, however, you find that your Danby refrigerator isn’t making ice, it could be frustrating and frustrating. A Danby refrigerator might not make ice due to various reasons, including a blocked water line or a defective ice maker. In this article we’ll look at the most common causes for this issue and provide you with steps-by-step directions for fixing a Danby refrigerator that is not making the ice. You’ll quickly be able to determine the issue and have your refrigerator producing ice again within a matter of minutes.
Common solutions to the following: My Danby refrigerator isn’t producing Ice
Danby Refrigerator Main Control Board Main Control Board of Danby Refrigerator
The Danby refrigerator’s main control board controls the voltage being transmitted to the ice maker. The icemaker might stop working when it’s not in good shape. Inspect the board for any signs of damage, or an issue with the component. After reviewing the wiring diagram for the Danby refrigerator, you may use a multimeter or a magnifying glass to determine whether the voltage is reaching the ice maker. The Freezer Temperature Must Be at or above 10 degrees F (12C). If the temperature of the freezer is higher than 10°F (12C), the icemaker cannot create ice cubes efficiently. The freezer temperature must be maintained between 5 and 0 degrees Fahrenheit (-18 to -15C) to allow the maker to function properly. The temperature of the freezer should not be too high. Also, ensure that the condenser fan is functioning properly and there’s no debris on the coils of condenser. You should also check for frost accumulation on the coils of the evaporator. The defrost system may have failed in the event that the evaporator coils have are covered in ice.
Danby Refrigerator Water Inlet Valve: The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. It will not allow water to flow through when the valve for water inlet is damaged or has low pressure. Danby’s ice maker will not create ice due to this. In order to function effectively, the valve has to be at or above 20psi. The water pressure should be at minimum 20 PSI. Use a multimeter to verify that the water pressure is sufficient. If the valve for water inlet has sufficient pressure and is getting electricity however the ice maker won’t fill with water to make ice, replace the valve that supplies water to the maker. Danby Refrigerator Ice Maker Assembly A component could be damaged. Because a lot of the components for ice makers are not available separately, you might need to purchase and replace the entire Danby ice maker assembly. When replacing the ice maker assembly check the water inlet valve, the water line and the fan. Replace the icemaker assembly in the event that none of these components is damaged and the temperature of the freezer is not below 15 degrees Fahrenheit.
Low Water Pressure in the Home Supply: It could mean that there is not enough water pressure. The water inlet valve supplies water to the water dispenser as well as ice makers. To perform correctly the valve that supplies water to the water dispenser must have a minimum pressure of 20 PSI. To determine whether the pressure of water is at least 20 psi, make sure to check the flow. Verify that the that the icemaker is “On” Check that the Danby Icemaker is on and that the paddle or arm is able to move freely. For models with ice dispensers in the door, with the door open make sure the indicator light stays on steadily as the flap for the ice maker and switch for the door are pressed. Danby Refrigerator Door Switch The door switch shuts off the water and ice dispenser when the Danby refrigerator’s door is opened. If the door switch is not working and the dispenser doesn’t turn on. A multimeter can be used to check for continuity in order to find out whether the door switches are damaged. Replace the door switch if it does not maintain continuity following activation.
Danby Refrigerator Ice Level Control Board: Some Danby refrigerators use a infrared beam for detecting the level in the bucket of ice. If the ice level is at the top of the bucket, it interrupts the infrared beam. The control board turns off the icemaker. If the ice level falls below the beam, the control board signals the ice maker to make more ice. If the ice level control board fails then the maker will cease making ice. Make sure that the power source to the ice level control panel is functioning. Change the control board for ice if the icemaker isn’t working even though the ice control board is receiving electricity.
Danby Refrigerator Water filter: Clogged filters could block the flow of water into the dispenser, which can cause the maker of ice to cease working. To ensure proper water flow, and maintain high water quality, it is recommended that the filter is replaced every six to 12 months.
Danby Refrigerator Auger Motor: For the majority of Danby refrigerators to correctly dispensing ice the auger motor is used to rotate an auger blade that will move the frozen ice out of the bucket and down the chute of the dispenser. The motor that spins the auger could be worn out or defective and the ice may not be able to move through the chute. This could create an illusion that the ice maker is not work. You can test the auger motor by pulling out the bucket and turning the bucket auger using your hands. A multimeter is a good tool to test the electrical continuity of the motor, if it is able to rotate freely. If the motor of the auger does not have continuity, or if the motor is getting power but won’t run, replace the auger motor.
Danby Refrigerator Ice bucket: A lot of Danby refrigerators have a separate motor to spin an augerblade, which then pushes the ice out of the bucket into the chute. If the auger motor spins however the ice is not dispensing the ice, it may be damaged. For cracks or excessive wear, check the auger motor, the ice bucket, and drive coupler. If necessary change the ice bucket.
A Danby refrigerator not making ice is a frequent issue. There are a variety of reasons for this. There are many things you can do to make your appliance produce the ice it needs, such as the blockage of the water line, malfunctioning the ice maker, or problems with the thermostat. Follow the steps in this article to diagnose the problem and repair it with no professional assistance. Regular maintenance can help to avoid future problems. This includes taking care to clean the ice maker and making sure the water lines are clean. Don’t hesitate to call Danby when you require an ice maker.