An Maytag washing machine that stops mid-cycle could be a frustrating and confusing issue to handle. It’s not just annoying having to restart the cycle and then restart it again, but it could also be costly if the problem persists and requires professional repair. The homeowner can solve many reasons that a Maytag washer machines is stopped mid-cycle. In this article, we will go over some common reasons for a Maytag washing machine that stops mid-cycle. We’ll also offer step by step instructions for fixing the issue. We will help you troubleshoot the timer as well as check the door lock to make sure your Maytag washing machine is working as it should. We can assist you with fixing the Maytag washing machine if it ceases to work during the middle of the cycle. Incoming power problems Make sure that the power cord has been tightened. It must be secured tightly to ensure that there is constant electric power to the Maytag washer.
Washing Machine Control Board: Because a Maytag control board for a washing machine is the source of voltage for nearly every one of the washer’s electrical components. A malfunctioning board could cause the machine to stop in mid-cycle. The board may be inspected to look for indications of burned or shorted components. After reading the wiring diagram you can use a multimeter on the board to verify the power output connections.
Washing Machine Door Lock Motor and Switch Assembly: The Maytag door lock secures the door of the washer shut while in operation. Once the Maytag door to the washer is shut, the washer can begin working. The Maytag washer will not start operating when the Maytag door is not closed. If the door lock is defective, the washer might stop mid-cycle. Door locks can fail electronically or mechanically. Check the door lock to see if it is damaged. Replace the lock if it is broken or does not latch properly.
Switch for the lid of the washing machine assembly: This stops the washer spinning when the lid is opened. The washer may stop mid-cycle in the event that the lid switch is defective. To determine if the lid switch assembly is defective, use an instrument to test each of the lid switches for continuity. Replace any lid switch that is not in continuity.
Insufficient water supply: Be sure that the cold water is running into the tub. The Maytag washer won’t start the rinse cycle if cold water supply is too slow or isn’t reaching the tub. It could be because of a blocked water inlet valve or a partially closed main water supply valve or low pressure water coming from your home.
Washing Machine Water Inlet Valve: In the process of washing, the water inlet valve opens to allow water to enter the wash tub. If the water inlet valve is damaged, the washer will wait for water to flow into the washer, which causes it to stop in mid-cycle. A multimeter can be used to check for continuity in the valve that opens water. Replace the valve for water inlet to ensure it has continuity.
Washing Machine Drain Pump: A Maytag washing machine drain pump helps in removing the water from the tub through forcing the water to go through a drain hose into an empty laundry tub or drain pipe. Since water may be drained from the tub multiple times throughout a wash cycle the malfunctioning drain pump may stop the washer in mid-cycle. If you find that there is water in the tub after the washer is stopped, look at the drain pump for obstruction. To determine if the drain pump is functioning correctly, you can test it with the multimeter.
Washing Machine Main Control Board: The control board on the main board could be in a state of deficiency. This is not a common problem. Before replacing the control board in the main make sure you check all the parts that are more likely to fail.
Washing Machine Timer: The timer might be damaged. When diagnosing the timer, prior to replacing the timer, first look over all of the often defective parts. To check if the timing device is defective, consult the wiring diagram of your washer and utilize a multimeter to check the continuity of the timer.
In conclusion, the issue of a Maytag washing machine that is stopped mid-cycle may be a major issue however, it’s usually quite simple to resolve. By following the steps outlined in this post, you will be able to diagnose and fix common issues such as clogged filters, defective door locks and improper timer settings. Always unplug the washer before you attempt any repairs, and if you are unsure about any aspect of the process you should read the instruction manual from the manufacturer or consult a professional assistance. With a little patience and a bit of time it is possible to have your Maytag washing machine operating without issue, and avoid the hassle of having to restart the cycle , and the cost of repairs. Keep an eye on the machine and examine if there is a problem and take the necessary steps.