A Roper washer that can’t move to the next cycle could be frustrating and complicated to address. This issue can result from a variety of reasons, from the simplest to complex. We’ll discuss the most frequently-cited reasons why the Roper washer isn’t advancing into the next cycle, and then provide step-by-step instructions on how to fix the issue. Whether you’re a seasoned DIYer or are a novice fixer-upper, this guide will assist you to fix your Roper washer back to running in no time. It all depends on what type of Roper washer you own. Top-loading Roper washers will not advance to the spin or drain cycle when the lid switch fails. A Roper washer that doesn’t complete the cycle may be suffering from a malfunctioning timer or malfunctioning water-level pressure switch. A defective or malfunctioning drain pump, or shifter assembly for a top load vertical modular Roper washer can result in it stopping mid-cycle. The washer may be stopped mid-cycle if it has excessive suds. A Roper front-loader may be stopped because of a damaged door lock on the washer, a failed main controller board, or a defective motor control board. When the washer detects an issue, it will send an error code digitally to the controller board. This could cause the cycle to stop. These repairs may be able to solve your Roper Washer Issue.
Switch the lid off of the washer: The lid switch on a top-loading Roper washing machine is a safety switch that checks if the lid on the washer is shut. The lid must be shut as the basket spins. in the event that the Roper washer isn’t aware that the lid is open the machine will not spin or drain following the wash cycle. Some top-load Roper models need the lid of the washer to be closed prior to the time the drive motor runs. Top-load Roper washers with top load can’t fill even if the lid remains open. If the switch on the lid doesn’t know if the lid is shut then replace the switch.
Replace the Roper washer’s washer shifter assembly: The shifter assembly, also known as the actuator-in a top-load washer is mounted on the lower part of the gear case. The motor in the shifter assembly moves the drive system’s position between spin and agitation mode. The sensor in the shifter will monitor the position of drive system during the washing cycle. If the sensor, the motor or mechanical components of the shifter assembly fail, the washing machine will stop and signal an error code.
Replace the shifter assembly in case it fails: The Roper washer’s door lock assembly must be replaced. A front-load Roper washer is equipped with a safety switch as well as a latch and locking mechanism. The door will not lock in the event that any of the parts fail while it is open. If a component fails while the door closed, it will not be able to open. Replace the entire assembly in case any component fails.
Replace the Roper washer’s main control board: The main electronic control board, also referred to the mother board regulates the time and operation of the washer’s component functions. It regulates the fill valves along with the drive motor and the drain pump.
Replace the Roper washer timer: The timer -is also known as a selector is the dial you use to set the cycle for a Roper washing machine using mechanical controls. The timer regulates the Roper washing machine’s cycle, from filling up to spin. Replace the timer in the event that it fails to move the washer through its cycles.
Replace or repair the Roper drain pump for the washer: The drain pump is responsible for draining water from the washer during washing cycles. The impeller blades, seal , and bearings of the pump may wear out. The belt on a belt-driven pump can wear out, and the pulley can shear off. The sound of a humming when you notice that the Roper washer is full of water can be an indicator of a malfunctioning pump. In certain instances, you can repair the pump by cleaning it of obstructions and fixing wiring issues or replacing a seal. If the pump cannot be repaired or rebuilt, then replace it.
Replace the Roper washer motor control board: The motor control board is a board for circuit control found in a front load Roper washer that’s usually in the bottom of the washer right next to the drive motor. It controls the speed of the drive motor, as well as the direction it’s directed to for spinning and tumble actions. If the motor doesn’t run the motor control board may need to be replaced. Replace the
Roper washer’s water pressure switch: The water-level pressure sensor is able to detect the level of the water inside the tub. The washer will not be able to fill correctly if its water-level pressure sensor has been damaged. It could not be filled properly or overfill, even to the level of overflowing. If the pressure switch isn’t able to accurately determine and control the water level in the washer, change it.