Perhaps you’ve experienced the frustration of the frustration of a Maytag washing machine that kept from filling up with water. Not only does it waste the water and energy it can also cause damage to your floors or your Maytag washer itself. We’ll go over common issues and provide step-by-step instructions to fix a Maytag washing machine that continues to fill up with water. Whether you’re a seasoned DIYer or a complete beginner, you’ll get the information you need to help you get your Maytag washing machine back into good working properly. If you’re determined to fix your dangling Maytag washer, then keep reading!
Water Inlet Valve
The Water Inlet Valve of your Maytag washing machine can be used to water the tub with cold, hot or warm water. The valve operates using electronic solenoids controlled by the timer or electronic control board and the water level control switch or pressure switch. If your Maytag washer does not fill during a cycle the valve that allows water to enter may be at fault. To confirm that the valve is to blame remove the Maytag washer as soon as the symptom appears. If the Maytag washer continues to fill, the valve to let water into the washer is damaged. If the washer stops filling, then the problem is related to the electrical circuit that regulates the valve. How to check the water inlet valve of a Maytag washing machine with a multimeter:
- Similar to other tests, ensure that you’ve disconnected the power source from your Maytag appliance prior to beginning the test as you’ll be handling electrical components.
- Locate and pull out the valve that opens your water supply. It is located behind the connections to the hose. To open it, you’ll require the rear panel to be taken off.
- Inspect the valve for signs of wear or damage. The valve comes with screens in it. Examine these screens for any debris, be sure to do this with care because these screens aren’t replaceable and if they get damaged you’ll have to replace the entire valve.
- Make use of a multimeter to contact the valve’s terminals ports by using Rx1. You will get a distinct reading for every model. Look up your manual to learn what readings you should expect to receive.
- You’ll require a replacement Maytag water inlet valve when the valve is damaged or the test results are not consistent with the recommendations.
Level switch & pressure switch & air dome tube
The water level switch, which is activated by water pressure, can be used to adjust the level of water within the tub. The control panel is likely to have this part. It will be attached to the tub using the use of a hose or air dome tube. This switch can be located under the tub in Maytag washers, which have an electronic control. When the water is filled into the tub, it will compress the air inside the tube, pushing against the diaphragm of the switch. The switch controls the water inlet valve , and shut off the valve at the proper level of water. If the tube has a leak or is plugged in, not enough pressure could be created to activate the switch and the washer might overfill. The switch might be defective and result in the washer filling overfilling. How to check the water level switch of a Maytag washing machine
- It will involve electrical components so make sure you disconnect your washing machine from the power source prior to beginning.
- Open your Maytag cabinet for your washer to locate and take off the switch for water level, as well as the air dome tube. Once removed, plug one end of the air dome tube, place it in water and blow into the other end. Undamaged hoses aren’t likely to produce bubbles.
- Check the hose as well as the valve for any indications of wear, cracks, or damage.
- If there are any issues during the above inspections then you might require a Maytag replacement water switch for the level. A Maytag washing machine that isn’t filled with water can lead to difficult and costly issues. But, by identifying the most common causes for this problem and taking necessary steps to remedy it, you’ll save yourself time and money.
This article can help you fix the problem with your Maytag washer, regardless whether it’s a problem with the water level switch or the inlet valve. Before you begin any repairs you should review the instruction manual of the washer. The manual will outline specific procedures for troubleshooting, as well as safety precautions. If you’re unsure whether it’s possible to fix the issue at home, it’s best to hire a professional to do the repairs. Overall, with a bit of knowledge and the right strategy, you can fix a Maytag washer that isn’t filling with water and return to doing your laundry with ease.