How to Fix Maytag Washer That Has No Hot or Cold Water

A malfunctioning Maytag washer can be a very frustrating experience, particularly if it refuses to make use of hot or cold water. Not only is it frustrating to have to deal with dirty clothes, but it can also be costly to have professionals come in to solve the issue. The good news is that many issues related to hot and cold water in a Maytag washer are easily fixable by the owner. In this post, we’ll go over some common causes of a washer with no hot or cold water and offer step-by step instructions on how to resolve the issue. We’ll help you figure out how to fix the thermostat and check the water supply. If you’re struggling with a stubborn machine or just need to cut costs for repairs, keep reading to find out how you can fix a Maytag machine that doesn’t have hot or cold water.

Inlet Hoses and Screens

Maytag washers are connected to the household water supply via fill hoses. These hoses typically measure 4 to 5 feet in length and feature wire mesh or a plastic screen that connects to the faucet. The screen blocks sediment from entering the water inlet valve located in the back of the appliance. How to examine the hoses & screens on the Maytag washing machine:

1. This is an easy inspection, and you do not have to take apart your washing machine. Make sure whether the hoses have not become bent and the faucets are open.
2. Switch off the faucets and disconnect the fill lines from the inlet valve and look over the screens. Take out any debris or sediment that you see.
3. To make sure you have adequate water pressure to fill the hoses, put the hose’s ends in the tub or bucket and begin to turn on the faucet. Verify the hose’s filters for damage or dirt buildup when you don’t have enough pressure.
4. If you encounter issues in these inspections you will need Maytag screen and hose replacement.

Water Inlet Valve

The Water Inlet Valve of the Maytag washing machine will supply hot and cold water to the wash and rinse. The valve is equipped with two solenoids that operate inlets for both the hot and cold water supply. The electronic control or timer the water temperature cycle selector and the water pressure switch are the controls for the valve. The valve is controlled by the electronic control or timer along with the water temperature/cycle selector switch, and the water level/pressure switch. How to test the water intake valve within theMaytag washing machine using a multi-meter:

1. Before beginning this inspection ensure that you’ve disconnected the washer from power as well as the water source.
2. To remove the valve for test, take out all or part your Maytag washer cabinet. You’ll find the valve right behind the hose connectors.
3. Take a look at The Maytag washer’s valve for cracks, wear or damage. The valve has screens in it that could have gathered up dirt or debris, in which case it must be thoroughly cleaned. If these screens break the valve will have to replace the entire valve.
4. The resistance of a functioning valve can vary from model to model. Read the instruction manual to figure out the correct reading. Put the probes onto the terminals of the valve using the RX1 option on your multimeter. If you’re not getting continuity, you can use a Maytag replacement valve for the inlet.

Lid switch

The lid switch in top-load Maytag washers is a security device that prevents the motor circuit from operating in the event that the lid is opened. On certain models, the circuit for water inlet can also be controlled. These models have a lid switch that controls the power supply. It is important to check the lid switch in the event that the water inlet valve on your Maytag washer has stopped receiving power. How to test the lid switch in the Maytag washing machine:

1. Before beginning, verify that you have disconnected the plug on the plug in your Maytag washing machine.
2. To locate the switch, you will be required to remove the cabinet or top panel. Once you’ve found it, check that the levers and actuators aren’t damaged or stuck and also that the switch is being operated mechanically.
3. If there is no issue above, remove the switch in order to test it for continuity. Then set your multi-meter to Rx1.
4. Click the button to activate the switch. Then make use of the probes touch the terminals. The probes should be able to touch the terminals with a pressure that is between zero and nearly zero.
5. If you do not receive the same reading, you’ll need an Maytag lid switch replacement.

Selector Switch, also known as a Switch for Water Temperature Switch

The selector switch or the water temperature switch determines temperatures for the rinse and wash portions of the cycle. The switch creates a circuit to provide power to the right solenoids located on the water inlet valve. The temperature selector switch may be the problem in the case that there is no power to the solenoids on the water inlet valve. Test the switch on theMaytag washing machine using a multi-meter

1. Since you’ll be removing and testing electrical components, make sure that you unplug your Maytag washer prior to starting.
2. Switch off the selector on the appliance to test it, you will need to disassemble every part or all of your cabinet for your washer to get it. It’s usually connected to the frame of the Maytag washer machine.
3. Each button on the switch will be tested one-by-one. Start by placing probes on one button’s terminals. The reading should be infinity. After that, press the button to switch to zero. Press the button to turn the reading back into infinity.
4. If your readings do not match the above descriptions It is necessary to replace your selector switch by Maytag.

Water Level Pressure Switch

The water level switch is a switch that operates under pressure that forms part of the water inlet valve circuit. This switch is normally situated in the back of the control panel and may contain a hose, or a dome tube connecting it to the tub. For Maytag washers with electronic control, this switch can be situated in the sump area below the tub. The switch may stop supplying electricity to the valve for water supply when it’s damaged. How do you check the level of water on a Maytag washer machine:

1. Before you begin, unplug the power supply from the Maytag appliance.
2. A malfunctioning air dome or switch could cause the same symptoms as the defective switch. You can open the cabinet of your washer to locate the issue and take out the air dome hose. With one end sealed, blow into the other end while the hose is submerged in water. There should be no bubbles will rise to the surface.
3. Take the switch off the appliance to check it for any signs of wear, damage or cracking. It will likely be located in the sump, under the tub or behind your control panel.
4. If you find any flaws in your components while conducting these checks it is possible that you require a Maytag replacement water level switch.

Timer or Electronic Control

The timer or electronic control is used to decide when the valve for water inlet receives energy. The mechanical timer is comprised of several electrical contacts operated by a motor that is small and cams. These contacts supply energy to the water intake valve circuit during the rinse, rinse and fill portions of the cycle. How to test the timer control of the Maytag washer using the multimeter:

1. To find the timer, disconnect your Maytag washer and then take off its control panel and its rear panel.
2. Take the timer out of the Maytag washer. Do not pull directly on the wires; instead, pull the metal connectors connected to the wires.
3. Place the probes at the motor’s end. The test is for continuity and should receive a reading of zero or close to zero.
4. You’ll require a replacement Maytag timer if your test results are different.

In the end it is clear that the issue of a Maytag washer that does not have hot or cold water may be a difficult issue to address, however, it is often a relatively easy fix. You can identify the cause of common issues such as blocked pipes, malfunctioning valves or improper water temperature settings by following the steps in this post. Before you attempt any repair to your Maytag washer, unplug it. If you have any questions then refer to the manual or talk to a specialist. You can fix your Maytag washer working again quickly and efficiently with patience and time. This will spare you the trouble of washing your clothes as well as the expense of repair.