How to Fix Inglis Washer That Has No Hot or Cold Water

A Inglis washer that’s not functioning effectively can create a myriad of problems, especially when it’s not using cold or hot water. It can be a hassle washing dirty clothes, and can cost a lot to employ a professional to repair the issue. A number of problems with hot or cold water of the Inglis washer are easily fixed by the home owner. In this article, we’ll discuss the most common reasons why a washer has no hot or cold water and give step-by-step directions on how to fix the problem. We’ll help you fix your thermostat and test the water supply. You can save money in the long run by not needing to repair your washer that’s not hot or cold.

Inlet Hoses and Screens

Inglis washers are connected to the household water supply by fill hoses. These hoses typically measure approximately 4-5 feet in length. They also have wire mesh or a plastic screen at the end which connects the faucet. This screen helps prevent sediment from getting into the water inlet valve on the appliance. It’s located at the back. How to examine the hoses and screens on the Inglis washing machine

1. This is a simple test; you’ll not have to take apart the washer. Check that the hoses do not appear to be damaged and that the faucets are fully open.
2. Turn off the faucets, disconnect the fill hoses and the valve at the inlet and examine the screens that form part of the valve. Get rid of any dirt or sediment you can find.
3. In order to determine whether you have the pressure for your hoses, place the ends of the hose into a tub or bucket and switch on the faucet. If you have minimal pressure, inspect the screens in the hose for signs of dirt accumulation or any damage.
4. If you find any issues in these inspections you will need Inglis screen and hose replacement.

Water Inlet Valve

The Water Inlet Valve of your Inglis washing machine will supply cold and hot water for washing and rinse. The valve is equipped with two solenoids that operate inlets for hot and cold water supplies. The timer or electronic control, water temperature cycle selector and the water pressure switch regulate the valve. The timer, electronic control, water temperature/cycle selector and pressure switches control the valve. How to test the water inlet valve within an Inglis washing machine using a multi-meter

1. Before you start this test be sure that you’ve disconnected your washing machine from the power source and water source.
2. In order to remove the valve for testing, you’ll have to remove all or part of your Inglis washer’s cabinet. The valve will be in the middle of the hose connection.
3. For evidence of cracking, damage or wear, visually look at your Inglis washer’s valve. There are screens within the valve that have become clogged with dirt and debris. If this happens you should clean it thoroughly. If not, you’ll have to replace the entire valve.
4. The resistance of a operating valve can vary from model to model, look up the manual for your particular model to determine what the result of your test should be. To test for continuity, place the probes on the valve’s terminals using your multi-meter set for Rx1. If you don’t get continuity, you could use an Inglis replacement inlet valve.

Lid switch

The lid switch on top-load Inglis washing machine is a safety feature which stops the motor circuit from operating in the event that the lid is open. Certain models also have a water inlet valve circuit that is able to be controlled. If the lid switch fails on these models, then power is not able to be delivered to the water inlet valve. If you’ve found that the water inlet valve of your Inglis washer isn’t getting electricity, you need to check the lid switch. How to test the lid switch on theInglis washer:

1. Before starting, be sure that your Inglis washer is not plugged in.
2. To locate the switch you have to remove the cabinet or top panel. Once you’ve located it, ensure that the levers or actuators aren’t squeezing or damaged and that the switch is operated mechanically.
3. If there aren’t any issues above, take the switch off to check for continuity . Set your multimeter at Rx1.
4. Press the button to turn on the switch. Then make use of the probes reach the terminals. You should get a reading of zero or nearly zero.
5. If you see a reading that isn’t near or zero, then you’ll be required to replace the Inglis lid switch.

Selector Switch, also known as a Switch for Water Temperature Switch

The selector switch, also known as a water temperature switch selects temperatures for the rinse or wash portion of the process. The switch creates a circuit to provide power to the correct solenoids on the valve that opens the water. The temperature switch might be the cause when you don’t have power to the solenoids on the valve that opens water. How to test the switch on the Inglis washing machine with a multi-meter:

1. Because you’ll be taking out and testing electrical components, ensure that you unplug your Inglis washing machine prior to starting.
2. To test your appliance, remove the switch that controls your selector. You’ll also have to disassemble each of the cabinets for the washer. For the majority of models, it’s connected to the frame of the Inglis washing machine.
3. You will be testing the buttons on the switch one at each time. Begin by placing probes on the terminals for one button, your reading should be infinity . At this point, press the button. This should change your reading to zero and then press the other button, this should change your reading back to zero.
4. If your readings differ from those listed above, you’ll require a Inglis replacement switch for the selector.

Water Level Pressure Switch

The water level switch is a switch that operates under pressure which is part of the valve for water inlet. This switch is normally situated in the back of the control panel and may have a hose or air dome tube connecting it to the tub. For Inglis washers that have an electronic control, this switch might be located at the sump, which is below the tub. If the switch is defective it might not be able to supply power to the valve used to supply water. How do you check the water level switch on aInglis washer:

1. As with all repairs, disconnect the power source from your Inglis appliance prior to starting.
2. While the switch may be the issue but a defective air dome hose produces the same issues as a defective switch. Inspect the cabinet in your washer to identify the issue and then take off the air dome hose. While sealing one end and the other sealed, blow through the other and then submerge the hose in water. The hose should not bubble up and no bubbles are expected to rise up to the surface.
3. To check the appliance for indications of wear, cracks, damage or other issues take the switch off. It is likely to be on the bottom of the sump beneath the tub or behind the control panel.
4. If you notice any flaws on your part while carrying out these checks it is possible that you require Inglis replacement water level switch.

Electronic Control

The electronic controller or timer is used to control the time that the valve for water inlet receives power. The mechanical timer is comprised of many electrical contacts which are operated by a small motor and cams. These contacts will supply power to the water outlet valve circuit throughout the rinse, fill and rinse sections of the cycle. What can you do to check the control of the timer in the Inglis washing machine with a multi-meter:

1. To locate the timer, unplug your Inglis washer, then remove its control panel and its rear panel.
2. The timer must be removed from your Inglis washer Do not pull directly on the wires; instead, pull the connectors made of metal attached to the wires.
3. Set your multimeter to Rx1 while you press into the button (if necessary) connect the probes to the terminals that are connected to the motor (refer to the wiring diagram). The test is for continuity and should receive a reading of zero or nearly zero.
4. You’ll require a replacement Inglis timer if your test results are different. In conclusion, it is true that a Inglis washer that does not have hot or cold water could be a hassle to tackle, but it’s typically an easy fix.

If you follow the steps described in this post, you’ll be able to diagnose and address common issues like clogged hoses malfunctioning valves, and improper temperatures for the water. Remember to always unplug the Inglis washer prior to attempting any repairs, and if you are unsure about any aspect of the procedure, it is best to look up the manual for the manufacturer or seek out a professional assistance. It is possible to get your Inglis washer running again swiftly and efficiently with patience and time. This will save you the trouble of washing clothes , and the expense of repair.