You’ve probably experienced the frustration of an Hotpoint washing machine that was constantly filling up with water. This isn’t just a waste of the water and energy but it can also cause damage to your floors or even to your Hotpoint washing machine itself. We’ll discuss common problems and provide step-by-step instructions to fix a Hotpoint washing machine that continues to fill up with water. You can find all the information you need to solve your Hotpoint washer, no matter if you are a professional or a novice. So if you’re ready to fix that pesky Hotpoint washer, then keep reading!
Water Inlet Valve
The Water Inlet Valve that is on the inside of your Hotpoint washing machine allows you to provide the tub with hot, cold, warm, or cold water for washing and rinse cycles. The solenoids on the electrical circuits control the valve. They are controlled by the electronic control board, the timer and the water control switch for water level or the pressure switch. If your Hotpoint washer is filling up during a cycle it is possible that the valve for water inlet could be at fault. If your Hotpoint washer is filling up and fill, the water inlet valve may be the cause. The valve for water inlet could be malfunctioning if the washer fills constantly. If the washer ceases to fill it is due to the circuit electrical that is controlling the valve. How to test the water inlet valve of a Hotpoint washing machine with the multimeter: As with all other tests, be sure to have turned off the power supply to your Hotpoint appliance prior to beginning.
- You will be conducting electrical tests on the components.
- Find and remove your water inlet valve. It’s located just behind the connection to the hose. To get to it, you’ll need the panel on the back to be taken off.
- Take a look at the valve and look for signs of wear. You’ll need to replace the entire valve if it has screens.
- Make use of a multimeter to contact the terminals of the valve’s ports with Rx1. The reading you should receive is different from model to and you should consult your owner’s manual to find out what results your test will produce.
- You’ll require a replacement Hotpoint valve for water inlet in the event that the valve is damaged or your test results are not consistent with the recommended test results.
Water level switch pressure switch & air dome tube
The water level switch, which is activated by water pressure is used to set the water level within the tub. It is typically located behind the control panel, and it will have a hose or air dome tube that connects to the tub. The switch can be found beneath the tub in Hotpoint washers that have an electronic control. When water begins to fill the tub it will compress the air inside the tube and push it against the diaphragm of the switch. The switch will control the water inlet valve , and close the valve at the right level of water. The washer might overfill if it is damaged or leaky. The switch could be damaged and result in the washer filling too high. How do you check the water level in a Hotpoint washer:
- You will be working with electrical components so make sure you disconnect your washing machine from the electrical supply prior to beginning.
- Unlock your Hotpoint appliance’s cabinet to locate and then remove the switch for water level and the air dome tube. After the air dome tube is removed, place one end of it in the tank, and blow it into the other. Undamaged hoses will not produce bubbles.
- Examine the hose and valve for cracks, wear or damage. If you observe any problems following the above tests then you may require Hotpoint replacement Water Level Switch.
In conclusion, a Hotpoint washing machine that isn’t refilling with water is an aggravating and costly problem to deal with. You can cut down on time and cash by understanding the root of the issue and then taking the necessary steps to correct these issues. This article can help you resolve the issue with the problem with your Hotpoint washer, no matter whether it’s a problem in the water level switch or with the valve for inlet. Before you start any repairs you should review the instruction manual of the washer. It’ll give specific steps to troubleshoot and security precautions. If you’re not certain if the issue can be resolved at home, it’s better to get experts to handle repairs. With just a bit of knowledge and the right approach you can repair Hotpoint washers that won’t fill up with water. Then, get back to washing.