If you’ve had the unfortunate experience of dealing with an Haier washing machine that won’t stop filling up with water, you know how frustrating it can be. Not only does it waste water and energy, it could cause harm to your floors and even your Haier washer itself. In this article, we’ll take a look at the most common causes of this issue and give step-by-step instructions on how to fix a Haier washer that isn’t stopping filling up with water. No matter if you’re a skilled DIYer or an absolute novice, you’ll discover the necessary information to bring your Haier washing machine back in working in good working order. So if you’re ready to repair that nagging Haier washer, read on!
Water Inlet valve: The Water Inlet Valve located on your Haier washing machine allows you to supply the tub with hot, cold or warm water for the wash and rinse cycles. The solenoids on the electrical circuits control the valve. They are controlled by the electronic control board, the timer and the water control switch for water level or the pressure switch. If your Haier washer does not fill throughout the cycle then the water inlet valve could be at fault. To verify that the valve is in error remove the Haier washer once the issue is observed. If the Haier washer continues to fill, then the water inlet valve is inoperable. The problem may be in the electrical circuit controlling the valve. How to check the water inlet valve within the Haier washing machine using the multi-meter:
- Similar to other tests, make sure you’ve disconnected the electrical source of your Haier appliance prior to beginning as you’ll be working with electrical components.
- Find and remove your water inlet valve. It is most often found directly behind the hose connections It is necessary to take off the back panel to get it in place.
- Visually inspect the valve for signs of wear or damage. The valve has screens in it. Check these screens for any debris, be careful as these screens cannot be replaced and in the event that they become damaged you’ll have to replace the entire valve.
- Use a multimeter and touch the terminals of the valve’s ports with Rx1. The amount you should see will differ from model to, refer to your owner’s guide to figure out the type of you should receive from your test.
- You’ll require a replacement Haier water inlet valve in the event that the valve is damaged or the test results are not consistent with the recommendations.
Water level switch & pressure switch & air dome tube: The water level switch, which is activated by the pressure of water, is used to regulate the water level in the tub. The control panel typically contain this feature. It will be connected to the tub with either a hose or a dome tube. On Haier washers that use an electronic control this switch can be located in the bottom of the sump, below the tub. The water will fill the tub and expand the air inside, pressing against the diaphragm. The valve that opens the water will be controlled by the switch, which will shut off the valve when it reaches the right water level. The washer could overfill if it is damaged or leaky. The switch could be defective and cause the washer to fill overfilling. How do I check the water level in a Haier washer machine:
- You’ll be working with electrical components so make sure you disconnect the washer from the power supply prior to beginning.
- Open your Haier appliance’s cabinet to locate and remove the water level switch and the air dome tube. Once the air dome tube is removed, place one end of it in the water tank and blow it into the other. Hoses that are not damaged will not create bubbles.
- Examine the hose and valve for signs of wear, cracks or damage.
- If there are any problems during the above inspections it is possible that you require Haier replacement water switch to regulate the level.
A washing machine from Haier which isn’t able to fill with water can result in frustration and cost. By understanding the causes that are most likely to cause this issue and taking proper steps to correct it, you can reduce your time and expense. The issue could be a water level switch that is not working or a blocked valve for the inlet. The solutions described in this article will help you get your Haier washing machine back in working order. Before you begin any repairs, it’s a good idea review the instruction manual of the washer. It’ll give specific directions for troubleshooting as well as safety guidelines. If you’re not confident in your ability to fix the problem on your own It’s best to get an expert to help with the repair. With a little some knowledge and the correct approach it is possible to fix your Haier washer that isn’t filling with water and return to washing your laundry without difficulty.