If your Frigidaire washing machine’s timing doesn’t advance, it can be an annoyance and time-consuming issue to fix. There are a variety of ways to fix the issue. We’ll go over the most frequent reasons that Frigidaire washing machine won’t start , and provide step-by-step solutions. This guide is intended for experienced DIYers as well as those who are new in home repairs. It will guide you through how to get your Frigidaire washing machines running again within a matter of minutes.
Lid switch
The lid switch is a safety feature in top-loading Frigidaire washing machines. The lid switch is usually found under the main top, and has the lid projected or a pin connected to the lid. It will activate the switch once the lid is closed. The motor circuits and the timer are powered by the lid switch. Test the lid switch in aFrigidaire washing machine with a multi-meter
- Remove the plug from your Frigidaire washing machine.
- Remove the cabinet or top panel to find the switch on the lid.
- After finding the switch, ensure that all actuators and levers are clean and free from sticking.
- If there are no problems in the tests above, you can remove the switch and alter the Rx1 setting of your multimeter. Hold the switch’s button. Set the probes at the switch’s terminals. The probes should return a reading of zero.
- If you get a different reading, then you’ll need a replacement switch lid.
Timer and Timer Motor
The timer is the sole control for all features of the Frigidaire washer. A number of electrical contacts will be found on the timer. The contacts are controlled by a cam that is moved by a timer motor. Certain contacts of the timer are used to control the motor of the timer. If the timer on your washer will not advance it is possible that the timer or motor could be the cause. Test the timer and timer motor of aFrigidaire washing machine using a multi-meter
- Unplug your Frigidaire washing machine from power sources.
- Locate and remove the timer on your appliance. To gain access to the control panel and the rear panel, you will need to take them out.
- Set your multimeter’s Rx1 setting and then touch the probes at the motor’s end (refer to your wiring schematic). You’re testing for continuity. You should get an error of zero or close to zero.
- If your test produces different results, you’ll require to purchase a new timer.
Water level control
The water level control feature of Frigidaire washing machines permits users to switch on or off the water valve at certain levels and to also supply power to the timer motor to regulate the water level. If your washer fills but the timer is unable to advance you may have an issue with the water level switch. How do you check the control of water levels on aFrigidaire washing machines:
- Before beginning, disconnect the plug on your washer as you will be handling electrical components.
- Before you suspect the switch, you should eliminate the air dome hose as the cause of the issue. Take the cabinet off and eliminate the air dome pipe. Set the hose in the water and close the ends. Then blow air into each end to look for bubbles. It is also recommended to inspect the hose for cracks, wear or other obstructions.
- If you do not see any issues above, you might need a replacement water level switch.
Timer Knob, Dial & Skirt
The timer knob, or dial, is attached to the shaft of the timer . It turns as the timer progresses through a set of cycles. The timer knob may also be used to initiate the timer by pulling on the knob that activates an internal switch within the timer. The timer knob is usually made from plastic , and then reinforced by a keyed insert. The knob can crack or wear over time and cease to turn with the shaft. This can make it difficult to determine the correct timer for the desired time. The cause is that the dial to not move with the shaft as the cycle progresses. How do you inspect the knob for timers on the timer knob on a Frigidaire washer?
- Unplug the Frigidaire washer’s electrical supply.
- Locate the timer knob You will have to lift the rear panel or cabinet to access it from the rear of the timer.
- Inspect the knob to ensure that the timer is engaged when the knob is pulled out and pushed into.
- If it doesn’t engage it, you’ll require replacement knobs.
Drain Pump
A drain pump is a device which removes water from the Frigidaire washer tub after the rinse and wash parts. The washer from Frigidaire may not be able to detect the tub is empty in the event that the drain pump fails. If your washer is unable to continue at the end of the rinse or wash portions of the cycle, you should be sure that the drain pump is functioning correctly. Some models controlled electronically may display a fault code when this happens. If your Frigidaire washing machine displays an error code You can look up our list of appliances that show common fault codes to determine the root cause. How do you examine the drain pump on a Frigidaire washing machine?
- Unplug the Frigidaire washer.
- Locate your drain pump. You will have to remove the front panel or cabinet of your appliance to get to the pump.
- Once you’ve located the pump, you should inspect the connections and hoses that come off the pump for damages or leaks.
- You will need a replacement Pump If the leak is being pushed out of the pump.
Water Inlet Valve
The water valve that is inlet to supply cold and hot water to the Frigidaire washer during the filling phase of the cycle. At least two solenoids from an electric source will be able to open the valve. The valve that opens the water supply could be the cause if the washer stops moving throughout the cycle and stalls during the rinse fill or wash part. First, make sure that there are no kinks in the hoses for the inlet and they’re not obstructed. These should be fine. After that, you should check the continuity of the solenoids with the multimeter. How to test the water inlet valve in a Frigidaire washing machine using the aid of a multi-meter
- Check that you have disconnected the Frigidaire washing machine before starting.
- Locate the water valve and take it off. It is likely to be located just behind the hose connections It is necessary remove the entire or a part of the cabinet to get to it.
- The screens inside the valve for signs of buildup or debris be sure to do this in a safe manner because the screens can’t be replaced and if they are damaged , you’ll need an entirely new valve.
- Check your pump’s visual appearance for any signs of wear or damage, if none are found Set your multi-meter to Rx1 and place your probes on the terminals. Review the instruction manual for your model to determine what results this test should produce since it differs from model to model.
- If the reading you receive isn’t within the acceptable range, for instance, if you are reading infinity or your valve appears to be damaged and you require replacement valves. replacement water inlet valve.