How to Fix Frigidaire Washer That Has No Hot or Cold Water

A Frigidaire washer that’s not operating properly could cause a number of problems, particularly in the event that it isn’t using hot or cold water. It’s not just frustrating having to clean up dirty clothes, but it can also be costly to have an expert come in to fix the problem. Fortunately, many issues with hot and cold water in the Frigidaire washer can be fixed easily by the homeowner.

We’ll discuss the most common causes your washer doesn’t have hot or cold water and offer step-by-step suggestions. We’ll help you fix the thermostat and also check the water supply. If you’re faced with a faulty machine or just wish to save money for repairs, continue reading to learn how to fix a Frigidaire machine that doesn’t have hot or cold water. Inlet Hoses and Screens:Frigidaire washers are connected to the water supply by fill hoses. These hoses typically measure around 4-5 feet long and will usually include an aluminum or wire mesh screen that is inserted at the end of the hose. It connects to the faucet.

The screen prevents particles from entering the valve to let water into the appliance located on the back of your appliance. How to check the hoses and screens on theFrigidaire washing machine:

1. This is a simple check; you do not need to disassemble your washing machine. Start by ensuring that the hoses aren’t damaged and that the faucets are in good working order.
2. Shut off the faucets. remove the fill hoses from the valve at the inlet and then inspect the screens that form part of the valve. It is recommended to clean out any debris or sediment. To ensure that you have enough water pressure to fully fill your pipes, place the ends of the hose in a bucket or tub, then open the faucet. Check the hose screens for dirt or damage in the event that you do not have enough pressure.
3. You will need replacement screen and hoses from Frigidaire if you find any issues during these examinations.

Water Inlet Valve

The Water Inlet Valve in your Frigidaire washing machine will supply hot and cold water to washing and rinse. The valve is equipped with two solenoids operating inlets for hot and cold water supply. The electronic control or timer the water temperature cycle selector and the pressure water level switch control the valve. The valve is controlled by the electronic control or timer, the water temperature/cycle selector switch as well as the pressure/water level switch. How to test the valve for water inlet within aFrigidaire washing machine using a multi-meter:

1. Before starting this inspection make sure you’ve disconnected your washing machine from both the power and water source.
2. To remove the valve to test, you’ll need to take out the entire or a portion of your Frigidaire cabinet of your washer. The valve should be located directly behind the hose connections.
3. Check the Frigidaire washer’s valve to see if there is cracks, wear or damage. There could be screens inside the valve that are clogged with dirt and debris. If this occurs you must clean it thoroughly. In other cases, you’ll need to replace the whole valve.
4. The resistance of a properly operating valve differs from model to model. check the manual of your owner to determine what the results of your test should be. To test for continuity, connect the probes to the valve’s terminals with your multi-meter set to RX1. If you’re not able to find continuity, try using an Frigidaire replacement inlet valve.

Lid switch

The lid switch on top-load Frigidaire washing machines is a safety feature which stops the motor circuit from operating when the lid is opened. On certain models the water inlet valve circuit can also be controlled. There is lid switches that control the power source. If you’ve discovered that the water inlet valve in your Frigidaire washer isn’t receiving power, you must inspect the lid switch. How to test the switch that controls the lid on a Frigidaire washer:

1. Before you begin, ensure that you have disconnected the plug on the plug in your Frigidaire washing machine. To locate the switch, you have to remove the cabinet or top panel.
2. Once you have located it, verify that the levers and actuators aren’t damaged or stuck and also that the switch is operated mechanically.
3. If there are no issues above, remove the switch in order to test it for continuity . Then set your multi-meter to Rx1.
4. While pressing in on the switch’s button, press to the terminals using probes. The probes should contact the terminals with a pressure between zero and almost zero. 5.If you get a different reading, then you’ll need a Frigidaire replacement lid switch.

Selector Swap Or Water Temperature Switch

The selector switch, or the water temperature switch, selects the temperature of the water that will be utilized for the rinse and wash portions of the. The switch is able to provide power to the proper solenoids of the valve that opens the water. If you don’t have power at the solenoids on the valve for water inlet The temperature selector switch might be in error. How to test aFrigidaire washing-machine selector switch using a multimeter

1. Since you’ll be removing and testing electrical components, ensure that you disconnect your Frigidaire washer prior to starting.
2. Take the selector switch off the appliance to test it, you will need to disassemble all or part of your cabinet in order to access it. It’s typically attached to the frame of the Frigidaire washer machine.
3. You will be testing the switches’ buttons one at each. Start by placing the probes onto the terminals for one button Your reading should be infinity . At this point, press the button. This will alter your reading to zero and then press the other button and it will alter the reading back to infinity.
4. If you get readings that are not consistent with the above descriptions You will have to change your selector switch by Frigidaire.

Water Pressure Switch

The water level switch, which is a part of the circuit for water valves and is a pressure-activated device. The switch is usually located behind the control panel, and it will contain a hose, or a dome tube that connects it to the tub. This switch is usually located underneath the tub on Frigidaire washers that have electronic controls. If the switch is not working, it may not supply power to the valve for water inlet. Test the water level switch on theFrigidaire washing machine:

1. In the same way as most repairs, unplug the power source to your Frigidaire appliance before starting.
2. A faulty air dome or switch can cause similar symptoms to the malfunctioning switch. Find out if the hose is the issue by opening your cabinet for your washer and removing the air dome the hose. While sealing one end and the other sealed, blow through another end, while the hose is submerged in water. No bubbles should appear on the surface.
3. Remove the switch from the appliance to examine the switch for indications of damage, wear, or cracks. It is likely to be on the bottom of the sump beneath the tub, or in the area in the area behind the control panel.
4. You may need a replacement water level switch from Frigidaire if you discover any defects while performing the examinations.

Timer Or Electronic Control

The timer or electronic control is used to decide whether the valve that is used to supply water receives energy. The mechanical timer will have an array of electrical contacts which are operated with a small motor and cams. In the fill, wash and rinse fill parts of the cycle, these connections will provide power to the water outlet valve circuit. What can you do to check the timer control on aFrigidaire washing machine with a multi-meter:

1. To locate the timer, unplug your Frigidaire washer and remove the control panel and the rear panel.
2. The timer should be taken off of your Frigidaire washer. Don’t pull the wires directly but instead, pull on the connectors.
3. Set the probes on the motor’s end. The test is for continuity, and you should get an error of zero or close to zero.
4. If your test shows an unrelated result it is time to get a Frigidaire replacement timer. A Frigidaire washer that doesn’t have hot or cold water is a frustrating problem that can be hard to fix, but it’s often quite simple.

You can troubleshoot common problems such as clogged pipes, defective valves, and inadequate water temperature settings by following the steps in this post. Before you make any repair to your Frigidaire washer, unplug it. If there are any issues then refer to the manual or talk to a specialist. You can make your Frigidaire washer back in working order quickly and efficiently with a little patience and time. This will save you the hassle of washing clothes and the cost of repair.