Electrolux washers that do not move into the next cycle of washing can cause frustration and confusion. There are many possibilities for the cause and they range from easy to complicated. In this post, we’ll discuss the most frequently-cited reasons for why Electrolux’s washer won’t proceed to the next cycle and provide step-by-step instructions on how to diagnose and fix the issue. Whether you’re a seasoned DIYer or a first-time fixer-upper, this guide will guide you to get your Electrolux washing machine back into working order in no time. It all depends on the kind of Electrolux washer are using. A top-loading Electrolux washing machine cannot advance to the spin or drain cycle in the event that the lid switch malfunctions.
Electrolux washers that don’t finish their cycle could also have a malfunctioning timing device or defective water-level pressure switches. In a vertical top-load modular Electrolux washer a faulty shifter assembly or a failed drain pump can cause the washer mid-cycle. In addition, excessive suds can cause this washer to stop working before the cycle completes. For the front load Electrolux washer, a malfunctioning washer door lock assembly or the main electronic control board, or faulty motor control board can cause the Electrolux washer from finishing the cycle. When the washer detects an issue, it’ll send a code of error to the controller board. This may cause the cycle to be stopped.
These Repairs May Help Solve Electrolux Washer Problems
Replace the switch that controls the lid on the washer: The switch for the lid on top-load washers from Electrolux is an emergency switch that is used to determine if the lid is closed. If the basket turns, the lid has to be closed. Otherwise, the washer will not drain or spin. Certain top-load Electrolux models require that the washer lid be closed before the drive motor starts to spin. Top-load Electrolux washers with top load cannot be filled when the lid is opened. Replace the switch in the event that the lid switch isn’t able to detect when the lid is shut.
Replace the Electrolux washer shifter assembly: The shifter assembly, also referred to as the actuator inside a top load washer is mounted to the bottom of the gearcase. The motor of the shifter assembly shifts the drive system’s direction between spin mode and the agitation mode. The location of the drive system is monitored by a sensor mounted on the shifter. The washer will stop when the motor, sensor or mechanical part of the assembly for the shifter fails and issue an error code. Replace the shifter assembly if it fails. The Electrolux washer’s door lock assembly is in need of replacement. A front-load Electrolux washer is equipped with a safety switch that is latchable, as well as a locking mechanism. If any of these components fails while the door is opened, the door won’t lock. If a component fails when the door is closed, the door will not open. If a component fails, replace the entire assembly.
Replace the Electrolux washer’s main control boar :The main electronic control board, also called the mother board regulates the timing and execution of washer component functions. It controls the fill valves, the drive motor and the drain pump.
Change the Electrolux washer timer: The timer often referred to the cycle selector, is the dial is used to control the timer of a Electrolux washing-machine with mechanical controls. The timer is what makes the Electrolux washer go through cycles, starting with the initial filling up until the final spin. Replace the timer if it fails to advance the washer through its cycle. Repair or replace the
Electrolux washer drain pump: The drain pump is the one responsible for draining water out of the washer’s washing cycle. The impeller blades, seal and bearings of the pump may wear out. The belt that drives belt-driven pump may break and the pulley can shear off. A humming sound during the time that you notice that the Electrolux washer is flooded is a common sign of a failed pump. In some cases you can fix the pump by cleaning the debris out as well as fixing wiring problems or replacing an impeller. If the pump cannot be repaired or rebuilt, replace it.
Replacing the Electrolux washer motor control board: The motor control board is a control circuit found in a front load Electrolux washer that’s usually in the lower portion of the washing machine right next to the drive motor. It monitors and controls the drive motor’s speed and direction for the tumble and spin actions throughout the cycle. The motor control board may need to be replaced if the motor stops running.
Replace the Electrolux washer’s water level pressure switch: The water-level pressure sensor measures the water level within the tub. If the water-level pressure switch is broken, the washing machine will not be able to fill correctly. It may not fill as it should or it could overfill to the point where it overflows. If the pressure switch isn’t able to precisely detect and regulate the water level inside the washer, change it.