How to Fix Crosley Washer That Has No Hot or Cold Water

A damaged Crosley washer can cause big hassle, especially if it refuses to use cold or hot water. Not only is it a hassle to wash dirty clothes, but it may cost a lot of money to have professionals come in to solve the issue. A lot of issues related to hot or cold water in the Crosley washer are easily fixed by the home owner. The following article will cover the most common reasons your machine doesn’t have hot or cold water, and offer step-by step solutions. We’ll help you fix the thermostat as well as check the supply of water. If you’re faced with a stubborn machine or you just wish to save money on repairs, read this article to find out how to fix a Crosley washer that doesn’t have hot or cold water.

Inlet Hoses and Screens

Crosley washers are connected to household water supply using fill hoses. They typically measure around 4-5 feet long and have wire mesh or a plastic screen on the end which connects to the faucet. The screen stops sediment from entering the valve that allows water to enter that is situated at the back of your appliance. How to check the condition of your Crosley washing machines screens and hoses

1. Start by making sure that the faucets and hoses are clean.
2. Turn off the faucets then disconnect the lines of fill from the inlet valve and inspect the screens. Make sure to remove any sediment or debris.
3. To ensure that there is enough pressure to fill the hoses place the hose’s end in a bucket or tub and start the faucet. If you are experiencing low pressure check the screens inside the hose for any dirt accumulation or any damage.
4. You’ll need to purchase replacement screens and hoses from Crosley should you notice any issues during these examinations.

Water Inlet Valve

The Water Inlet Valve of your Crosley washing machine provides hot and cold water to the rinse and wash. Two solenoids are used to control the inlets that provide hot and cold water. The timer or electronic control the water temperature cycle selector as well as the water level pressure switch are the controls for the valve. The valve is controlled via the timer or electronic control and the cycle selector for water temperature switch, and the water level/pressure switch. How to test the water intake valve within a Crosley washing machine with a multi-meter

1. Before you start this test ensure that you’ve removed your washer from both power and water source.
2. In order to take out the valve for testing, it is necessary to remove all or part of the Crosley cabinet of your washer. The valve should be found just behind the hose connections.
3. Looking for indications of cracks, damage, or wear, visually check the Crosley washer’s valve. There might be screens inside the valve that have been blocked by dirt and other debris. If this is the case, it is best to clean it thoroughly. If not, you’ll have to replace the entire valve.
4. The resistance of a functioning valve will vary from model to model. Refer to your manual to determine what your reading should be. For testing for continuity place the probes on the valve’s connections using your multi-meter set for Rx1.
5. If you do not get an indicator of continuity, then you’ll need a Crosley replacement valve for the water intake.

Lid switch

The lid switch for top-loading Crosley washing machines is a security feature that blocks the motor circuit from running when the lid is open. On certain models, the water inlet valve circuit is also controlled. If the lid switch is not functioning on these models, power is not able to be delivered to the water inlet valve. You should inspect the lid switch if the water inlet valve of your Crosley washer has stopped receiving power. How to inspect the lid switch in a Crosley washing machine:

1. Before starting, make sure you have disconnected your Crosley washing machine.
2. In order to find the switch, you will need to pull off the top panel or cabinet. Once you locate it, be sure the levers and actuators aren’t damaged or stuck. Also, ensure that the switch is being used mechanically.
3. If there aren’t any issues above, remove the switch to check to ensure continuity. You can also set your multi-meter to Rx1.
4. Press this button to activate the switch. Now utilize the probes to make contact with the terminals. It should give you a reading that is zero or very close to zero.
5. If you receive an amount that isn’t zero or close to zero, you’ll be required to replace the Crosley lid switch.

Selector Swap or Temperature Shift

The selector switch, also known as a water temperature switch, is used to select the temperature of water to be used in the wash and rinse phases of the. The switch serves to give power to the proper solenoids of the water intake valve. If there is no an electrical connection to the solenoids on the valve for water inlet and the temperature selector switch is the cause. What to do to test the Crosley washing-machine selector switch using a multimeter

1. Since you’ll be removing and conducting tests on electrical components, be sure that you unplug your Crosley washer prior to starting.
2. Remove the selector switch from the appliance. In order to check it out, you’ll need to disassemble the entire or a portion of your cabinet in order to access it. In many models, it’s connected to the frame of the Crosley washing machine.
3. It is your job to test the buttons on the switch one at a time. Begin by placing probes on the terminals of one button. Your reading should read infinity. Then push the button to shift the reading to zero. Then , press the button again to change the reading back to infinity.
4. If your readings differ from the readings described in the previous paragraph, you’ll need a Crosley switch to replace the selector.

Water Level Pressure Switch

The water level switch is a pressure-activated switch that is part of the water inlet valve circuit. The switch is usually located in the back of the control panel and will be fitted with a hose or an air dome tube connecting it to the tub. For Crosley washers that use an electronic control, this switch may be located at the sump below the tub. If the switch is not working and is not functioning properly, it could not provide power to the valve used to supply water. Test the water level control switch in a Crosley washing machine:

1. Before you begin, disconnect the power supply from your Crosley appliance.
2. A faulty air dome or switch can trigger similar symptoms as the malfunctioning switch. Open your washer’s cabinet to locate the issue and then remove the air dome hose. With one end sealed blow it into the other and then submerge the hose in water. There should be no bubbles will rise to the surface.
3. To look over the appliance to find indications of wear, cracks and damage or other issues take the switch off. The switch is most likely located within the sump area beneath the tub or behind your control panel.
4. You may need a replacement water level switch from Crosley in the event that you find any flaws while performing the above examinations.

Electronic Control

The electronic controller or timer is used to control when the water inlet valve receives electricity. The mechanical timer is comprised of several electrical contacts which are operated by a motor that is small and cams. In the fill, wash, and rinse fill parts of the cycle, these connections will supply energy to the water intake valve circuit. What can you do to check the control of the timer in aCrosley washing machine using the aid of a multi-meter

1. To locate the timer, unplug your Crosley washer and then take off its control panel and its rear panel.
2. The timer needs to be removed from your Crosley washer. Don’t pull directly on the wires; instead, pull on the metal connectors attached to the wires.
3. Set your multi-meter to Rx1 and, while pressing in on the button (if appropriate) put your probes in the terminals that control the motor (refer to the wiring diagram). You’re testing for continuity. You should receive the reading as near zero or zero.
4. If your test shows an unrelated result then you’ll need a Crosley replacement timer. In conclusion, it is true that a Crosley washer that does not have hot or cold water can be a hassle to address, however, it’s usually an simple fix.

There are many ways to troubleshoot common issues such as clogged pipes, damaged valves, or insufficient water temperature settings by following the guidelines in this article. Before making any repair to your Crosley washer, disconnect it. If you have any concerns you should consult the manual or contact a professional. With just a bit of patience and effort, you can have your Crosley washer operating smoothly and efficiently again, saving you the hassle of dirty clothes and the cost of repairs.