Bosch washers that don’t move to the next cycle of washing can cause frustration and confusion. There are several possible causes and they range from easy to complex. In this article, we will explore some of the most frequent reasons Bosch washers don’t move to the next cycle . We will also provide step-by-step instructions on how you can troubleshoot and solve the issue. No matter if you’re an experienced DIYer or are a novice fixer-upper, this guide will help you fix your Bosch washer back to functioning in no time. It’s all about the model of Bosch washer you are using. Top-loading Bosch washers cannot advance to the spin or drain cycle in the event that the lid switch malfunctions.
The Bosch washing machine that won’t finish the cycle could have a broken timer or malfunctioning water-level pressure switch. A malfunctioning or defective drain pump or shifter assembly for a top load vertical modular Bosch washing machine can result in it stopping in mid-cycle. The washer could also stop mid-cycle in the event that it is sludge-laden. The Bosch front-loader can be stopped because of a damaged door lock on the washer, a failed main controller board or a malfunctioning motor control board. This type of washer frequently emits a digital error message when the control of the washer detects a problem and ceases the cycle.
The following repair suggestions could assist in resolving your Bosch WASHER PROBLEM Replace the switch for the washer’s lid. The switch for the lid on top-load Bosch washers is a safety switch that determines whether the lid is closed. The lid must be shut as the basket spins. in the event that the Bosch washer incorrectly senses that the lid is closed it will not spin, and drain following the wash cycle. Some top-load Bosch models require that the lid be shut before the drive motor runs. An open lid prevents some top load Bosch washers from filling. Replace the switch if the lid switch fails to recognize whether the lid is closed.
Replace the Bosch washer’s washer shifter assembly: It is The shifter assembly also known as the actuator-in-a top-load washer is located on the bottom of the gear case. The shifter assembly’s motor shifts the drive system between the spin mode and the agitation mode. The location of the drive system is tracked through a sensor that is mounted within the shifter. The washing machine will cease the cycle if the motor, sensor or mechanical part of the shifter assembly fails, and send an error code. Replace the entire shifter assembly if it fails.
Replace the Bosch washer door lock assembly: The door lock assembly of a front-load Bosch washer has a safety switch that detects whether the door of the washer is shut, a latch and a locking mechanism. The door will not lock should any of the components fail when the door is opened. If one of the components fails while the door is closed, it will not open. Replace the entire assembly in case any component fails.
Replace the Bosch washer’s main control board: The main electronic control board, also known as the mother board, controls the timing and execution of washer’s components. It controls the fill valves, the drive motor and the drain pump.
Replace the Bosch washer timer: The timer is also referred to as the cycle selector, is the dial that you use to set the timer of a Bosch washing machine with mechanical controls. The timer lets the Bosch washer go through cycles, from initial filling until the final spin. If the timer does not move the washer through its cycles, it’s time to replace it.
Replace or repair the Bosch washer drainage pump: The drain pump is the one responsible for draining water out of the washer during wash cycles. The impeller blades, seal and bearings of the pump might wear out. The belt in belt-driven pump may break and the pulley’s ring can break off. If the Bosch washer is filled with water or hum, it could be an indication of a malfunctioning pump. It is possible to repair the pump in certain cases by removing the debris out of it, replacing a seal, or fixing wiring problems. You may replace the pump in cases where it’s impossible to repair or rebuild.
Replace the Bosch washer motor control board: The motor control board is a board for circuit control inside a front-load Bosch washer, which is usually located at the lower portion of the washing machine close to the drive motor. It monitors and controls the drive motor speed and direction for the spin and tumble actions that occur during the cycle. The motor control board could require replacement when the motor ceases to operate.
Replace the Bosch washer’s water level pressure switch: The water-level pressure sensor detects how much water is in the tub. The washer will not fill correctly if its water-level pressure sensor is damaged. It may not fill as it should or may overfill to the point where it overflows. Change the pressure switch if the device fails to recognize or control the water level of the washer.