A Blomber washing machine that doesn’t go to the next cycle could be an annoyance and a challenge to solve. This problem can result from a variety of reasons, from simple to complicated. In this article, we will look at the most common reasons why Blomber’s washer won’t advance to the next cycle . We will also offer step-by-step guidance on how to diagnose and resolve the issue. No matter if you’re an experienced DIYer or a first-time fixer-upper this guide will help resolve your Blomber washer back to functioning in no time. It’s all about the kind of Blomber washer own.
A top-loading Blomber washing machine will not progress to the drain or spin cycle if the lid switch fails. Blomber washers that aren’t able to finish their cycle could also have a malfunctioning timer or damaged water-level pressure switch. A malfunctioning or defective drain pump or shifter assembly on top-load vertical modular Blomber washing machine can result in it stopping mid-cycle. The washer could stop mid-cycle when it’s leaking a lot of suds. For a front-load Blomber washer, a malfunctioning door lock assembly of the washer and a failed main control board, or an inoperable motor control board may cause the Blomber washer from completing an entire cycle. This type of washer often emits a digital error message when the control for the washer detects a problem and stops the cycle.
These repairs could help solve Your Blomber Washer Problem
Replace the switch on the lid of the washer: The lid switch on top-loading Blomber washer is a safety switch that detects whether the lid of the washer is shut. The lid must be shut as the basket spins. if the Blomber washer incorrectly senses that the lid is opened, it won’t spin and drain following the wash cycle. Some top-load Blomber models require that the lid be closed before the drive motor starts to spin. The lid is not closed, which prevents certain top load Blomber washers from filling. If the switch on the lid doesn’t know if the lid is shut then replace the switch.
Change the Blomber washer-shifter component: The lower part of the gear box houses the switcher assembly, also known as the actuator-in-a top-load washer. The motor inside the shifter assembly moves the drive system from the spin mode to the agitation. The location of the drive system is tracked by a sensor located on the shifter. If the sensor, the motor or mechanical components of the shifter assembly fail, the washer ceases to function and will display an error code. If the shifter assembly malfunctions, replace it.
The Blomber washer’s door lock assembly is in need of replacement: A front-load Blomber washer comes with a safety switch as well as a latch and locking mechanism. If any of these components fail when the door is open, the door won’t lock; if a component fails while the door is shut, the door won’t open. Replace the entire assembly if a component fails.
Replace the Blomber washer main control board: The main electronic control board, also called the mother board, is responsible for the time and operation of the washer’s components. It regulates the drain and fill valves pumps, and the drive motor.
Replace the Blomber washer timer: The timer -also known as a cycle selector — is the dial you use to set the cycle on the Blomber washer with mechanical controls. The timer causes the Blomber washer go through its cycles, starting from the initial filling to final spin. If the timer fails to move the washer through its cycles, replace it.
Replace or repair the Blomber drain pump for the washer: The drain pump is the one responsible for draining water out of the washer’s washing cycle. The pump’s bearing may seize and seals can fail or the impeller blades might break. A belt-driven pump can have its belt break , and the pulley may be able to shear. The sound of a humming when the Blomber washer is full of water is a typical indication of a failing pump. Repairing the pump is possible in certain cases by removing the debris off it, replacing a seal, or fixing wiring issues. If the pump can’t be repaired or rebuilt, you must replace it.
Replace the Blomber washer’s motor control board: The motor control board is situated just in front of the drive motor in a Blomber front-load washer. It’s usually located at the inside the bottom of the washer. It controls the speed of the drive motor as well as the direction in which it’s directed to for motions of the spin and tumble. If the motor stops running the motor control board could need to be replaced.
Replace the Blomber washer water-level pressure switch: The water-level pressure switch measures the level of water in the tub. If the pressure switch for water level is not working, the washer won’t fill properly. It may not fill properly or may overfill until it spills over. If the pressure switch isn’t able to accurately monitor and control the water level inside the washer, you should replace it.