A malfunctioning Miele refrigerator and freezer can be a major inconvenience and a potential source of food spoilage and waste. If your Miele refrigerator and freezer are not providing food with the correct temperature, it’s important to solve the issue as soon as is possible. The good news is that many of the issues that cause refrigerators and freezers to become warm can be fixed by following a few easy troubleshooting steps. We’ll discuss the most frequent causes for warmer refrigerators and freezers from Miele and offer step-by-step solutions. It doesn’t matter if you’re a seasoned DIYer or novice, we’ll give you the necessary information to bring your refrigerator and freezer back to the proper temperature.
Cold Control or Temperature Control
The cold control is a temperature-controlled switch that supplies power to the compressor and fan circuits in the refrigerator. The control for cold could be out of calibration or defective if the fans and compressor aren’t operating properly. The normal temperature for fresh food is within the 38deg F range. The control should be set to mid-point. Check that the sensor bulb or capillary tube is in good health and that the wire terminals haven’t become loose or corroded.
Before you begin, unplug your Miele refrigerator. Then, unlock the Miele refrigerator’s doors and locate the control. It’s hidden behind the knob for temperature adjustment and can be found in the fresh food section of the control panel.
Take the control off the appliance and then turn it to the most warm setting. Next, adjust your multimeter to Rx1 so that it can connect to the terminals.
The probes are being checked for continuity. You should receive a reading of infinity. When the probes remain on the terminals, adjust the control to higher (colder) and higher settings. The reading should be changed to zero, indicating that you have continuity.
If your control fails either of the above tests, you will need a replacement Miele cold control & temperature control.
Motor for Evaporator Fan
The Miele Evaporator Fan Motor is used to circulate the cool air throughout the Miele refrigerator while the compressor is on. If the fan is not functioning properly then temperatures in the freezer section will increase slowly and temperatures in the fresh food section will rise more rapidly and the compressor will be running longer and more frequently than normal. When the compressor is running, you should also detect the evaporator fan operating simultaneously, along with the condenser fan which is close to the compressor.
How do you inspect a Miele refrigerator evaporator fan motor:
Connect the Miele refrigerator from its power source. Also, remove the cover of the evaporator It is located in the freezer compartment.
The motor shaft must turn at a brisk pace, with no resistance. try turning the shaft by hand to check whether there is resistance.
If there is a significant amount of ice on the motor, take it out of your freezer to see whether this resolves the issue. Also, inspect the motor for indications of wear and damage.
If it is not turning easily or is obvious that it is worn, you will require an replacement Miele evaporator fan motor.
Electronic Control Board
A control board with an electronic circuit could be used on some Miele refrigerators. Thermistors , also known as temperature sensors, are connected to the control board and used to keep track of temperatures in the fresh food and freezer compartments. The control board makes use of this information to regulate the operation of the compressor, fan motors and defrost systems. If the temperatures are excessively warm, then the electronic control could be at fault. Miele’s electronic controls can be complex and costly and are usually reliable. Therefore, you must first make sure that all the other components like the compressor, fans , and sensors are working properly before condemning the control. Certain manufacturers might provide specific data that can aid in diagnosing a malfunctioning control.
How to check the condition of your Miele refrigerator’s electronic control board
Make sure to unplug your refrigerator before you begin as you will be handling electrical components.
Locate and remove the control board that controls electronic devices from your appliance. It’s inside the Miele refrigerator, which is inside the control box, which is usually located at the top or side of the refrigerator.
Be sure to check your control panel for any indications of wear, damaged foil, burnt connections, arcing, or any other issue.
If you discover one of these you need a replacement electronic control board for Miele.
Temperature Sensor or Thermistor
In devices that employ the Electronic Control, a thermistor or temperature sensor may be used to monitor the freshness of food and the freezer temperature. It is a small capsule that is secured by a protective plastic shield and can vary in resistance according to the temperature. The control board utilizes this information to turn on the compressor and fan circuits as well as to operate the damper control on some models. If a sensor is damaged or malfunctioning, it could incorrectly signal the control board to shut off the compressor and fans and result in warmer than normal fresh food or freezer temperatures. Individual manufacturers may have specific information to check these sensors depending on the model that is involved and could also include an error code to the control board’s electronic component on some models.
How do I test a refrigerator’s temperature sensor or thermistor by using a multi-meter:
Begin by disconnecting your Miele refrigerator. Next, take off the front panel of your refrigerator to locate the main control board.
The main control board has the thermistor(s). For testing the thermistor(s) take it off from the appliance.
It is necessary to test your thermometers by placing them, along with the thermometer(s), in freezing water for five minutes until the temperature is raised to 32°F.
It should give you readings of 16,600 Ohms 5 Percent if you are using probes on the terminals and you have the multimeter on Rx1.
If you notice a reading that is not within this range, you’ll require a replacement Miele temperature sensor or thermosistor.
Defrost Timer
The defrost-timer is an electromechanical timer that runs a set of contacts that regulate the compressor circuit as well as the defrost heater circuit. A timer will trigger an defrost process every 8-10 hours. This occurs about once a daily. The defrost timer should terminate the defrost cycle after 20-30 minutes, and the compressor and fans will then begin.
How to test a refrigerator defrost timer using a multi-meter
Find the defrost timer you need by disconnecting your appliance from its power source. It’s located on the lower side of the refrigerator’s kickplate or on the control panel of the Miele refrigerator. It may also be on the back wall of the refrigerator.
After locating it, remove the defrost timer off the appliance in order to test it
Using a multi-meter on the Rx1 setting using one probe that is touching the terminal that is common to all (it is recommended to label it with “3” or “C”), touch the other lead to the three terminals at each time. Testing the first pair should result in a reading that is zero or close to zero signalling continuity. The reading that is zero or close to zero could also be indicated by the second pair. The third pair should be tested and the reading must read as if it was infinity.
If you are not receiving these readings, you will require an replacement timer from Miele.
Thermostat Defrosting
The Miele defrost thermostat acts as an safety thermostat that runs in series with the heater for defrost and can be used to stop the defrost cycle when the evaporator reaches a specific temperature, usually measured between 38 and 47 degrees Fahrenheit. If the thermostat is not working and remains open circuit then the defrost heater is not energized, and no defrosting can take place.
How do I test a thermostat for defrost in a fridge with a multi-meter:
Unplug your Miele refrigerator. Locate the thermostat that controls defrost. It could be located under the floor or on the back of freezers with tops. The thermostat for defrost is found on the side of a side-by-side refrigerator.
After you’ve located the device, go ahead and check it. It is necessary to take out all objects blocking your path, such as the contents of the freezer, shelves for freezers components of the ice maker, the inside rear, back or bottom panel.
Make sure your multi-meter is set to the Rx1 setting. Each probe must be placed on a thermostat wire. If the thermostat is at its lowest, the multi-meter will read zero. If the temperature is warm (anywhere between forty and 90 degrees Fahrenheit) This test should produce a reading of infinity.
If your results from your test are different from those listed here, you’ll need a replacement Miele thermostat.
Defrost Heater
The defrost heating device is the one that melts the ice and frost from the coils of evaporation. It is usually a wire filament that is enclosed within glass or aluminum tubes. There might be more than one heater depending on the form of the evaporator.
How do you test the defrost heating element using a multimeter
Before you begin, you must make sure that your appliance has been removed from the power source.
Locate your defrost heater. It can be located behind the front panel of the freezer area of your Miele refrigerator, or beneath the floor of the freezer section. Defrost heaters usually are located underneath the refrigerator’s evaporator coils. You must remove anything that is in your way such as the contents of the freezer, freezer shelves as well as icemaker components, and the inside rear, back or bottom panels.
Before you are able to test your heater’s defrost, you’ll need to remove it out of your fridge. The defrost heat source is connected by two wires. the wires are connected with slip-on connectors. Make sure you grasp the connectors using a firm grasp and remove them from their terminals. To assist you with this, you might need to use a pair needle-nosed scissors. Don’t pull on the wires by themselves.
Make use of your multi-meter to check the heater’s continuity. Place the tester’s leads at one terminal. The result should be anywhere between zero and infinity.
If you get a reading of zero or infinity you’ll need an replacement Miele heater for defrost..
Condenser Fan Motor
Most modern frost-free Miele refrigerators come with condenser coils cooled by fans. This normally located near the compressor on the bottom rear of the refrigerator. To reduce heat, the condenser motor moves air through the coil. If the Miele refrigerator is warmer than usual and the compressor is running almost continuously, then you might have a problem with the motor of the condenser. The evaporator motor and the compressor operate simultaneously. The compressor will function almost constantly if the fan motor ceases turning.
How do you inspect the motor in a fridge condenser fans:
Start by disconnecting your Miele refrigerator from the power source , then take off the access panel at the rear to locate the condenser motor. It is typically located in the lower rear of the appliance.
When you’ve located it, Look for any debris or obstructions that could be preventing the fan from moving freely. Also, you should inspect the motor of the condenser fan for any indications of damage or wear..
It is necessary to purchase a replacement Miele condenser fanmotor when the motor has been seized or worn.
A Miele refrigerator or freezer that is too hot could result in costly and frustrating issues. It is easy to resolve the majority of the problems associated with frigs and freezers that are warm by acquiring basic repair skills and a little troubleshooting. From looking at the temperature settings to cleaning the coils there are a variety of ways to restore proper cooling for your appliance. You can save money and make sure your food is safe and fresh by following these suggestions. To ensure safety and effectiveness, you should always consult an expert technician when you have questions regarding repairs.