A washing machine is a must-have appliance in most households. The washing process is automated, which saves time and energy. Many people must be faced with the problem of their washer stopping mid-cycle. The result is dirty clothes as well as a machine that’s not in a position to complete the task. There are a variety of reasons a washer may stop mid-cycle, including problems with the power supply, drainage system, or malfunctioning parts. The following article will cover the most frequent reasons why for a washer to stop working and provide practical solutions to address the issue.
Problem with Incoming Power
Check that the power cord is not loose. To ensure continuous electrical power, the cord must be securely plugged in.
Hotpoint Washing Machine Control Board
The Hotpoint washing machine controlboard supplies voltage to almost all of the components that power the washing machine. A faulty board can cause the washer to stop in the middle of a cycle. The board can be inspected to look for signs of burning, or a component that is shorted-out. You can also employ a multimeter for testing the terminals for power output on the board after reviewing the wiring diagram of your appliance.
Hotpoint Washing Machine Door Lock Motor and Switch Assembly
The door lock locks the Hotpoint door of the washer while it is in operation. Once the washer door is closed, the washer can begin operating. The door switch will stop the machine from functioning if the washer door isn’t closed. The washer can stop mid-way through the cycle in the event that the lock on the door fails. Door locks can fail electronically or mechanically. Inspect the door lock to find any damages. If the door lock appears damaged or fails to latch correctly then replace it. To find out if the lock has failed electrically check the diagram on your washer’s website and then use a multimeter to test each of the door lock switches for continuity. If one switch does not have continuity, replace the switch.
Hotpoint Washing Machine Lid Switch Assembly
The lid switch assembly keeps the Hotpoint washer from spinning when the lid is closed. If the lid switch assembly fails, the washer may stop mid-cycle. Multimeters can be used to examine each lid switch’s continuity. Replace any lid switch which has no continuity.
Hotpoint Insufficient Water Supply
Make sure that the cold water supply is entering the tub. If the flow of cold water is not flowing smoothly or does not enter the tub in any way The Hotpoint washer will shut off ahead of the rinse process while waiting for the tub to fill up. This is usually caused by an inlet valve that is blocked or the main valve for water supply closing partially or a low water supply pressure from the home.
Hotpoint Washing Machine Water Inlet Valve
During the rinse process, during the rinse cycle, Hotpoint water inlet valve is opened to let water enter the wash tub. The washer is waiting for water to flow into the washer in the event that the valve for water inlet is damaged. It will then shut off at the middle of the cycle. To determine if the water inlet valve is damaged, you can use the multimeter to test it for continuity. Replace the valve that is used for water inlet to ensure it has continuity.
Hotpoint Washing Machine Drain Pump
A Hotpoint washing machine drain pump helps to remove the water from the tub by forcing the water to go through a drain pipe to the laundry tub or drain pipe. Because water can be drained from the tub numerous times during the wash cycle, a defective drain pump may stop the washer in mid-cycle. If you find that there is water in the tub even after the washer is stopped, look at the drain pump for any obstruction. To test for electrical continuity using the multimeter. This will help you identify if the pump is functioning.
Hotpoint Washing Machine Main Control Board
It could be that the primary control board at Hotpoint might be malfunctioning. This is not a common problem. Before replacing the control board in the first place, be sure that you inspect the other parts that are more often malfunctioning.
Hotpoint Washing Machine Timer
The timer could be damaged. The timer is frequently misdiagnosed–before changing the timer, look over all the often defective parts. Check the wiring diagram of the washer in order to identify if the washer is defective. After that, utilize a multimeter to conduct continuity testing.
In conclusion the situation with an issue with a Hotpoint washer that stops mid-cycle could be an unpleasant experience There are many methods to fix the issue. By following the guidelines in this post, it is possible to determine and fix the root reason for the problem, whether it’s a clogged drain, damaged motor or an electrical issue. Be sure to unplug the device and take the necessary safety precautions prior to attempting any repairs. If you’re unsure about your abilities to fix the problem, it’s recommended to seek out a professional. It’s possible to fix your Hotpoint washer with just the help of a few patiences, skills and know-how. This will ensure that your clothes are clean and fresh everytime.