A washing machine is a must-have appliance for most households. The washing process is automated, which can save time and energy. But, one of the most common issues faced by many is when their Haier washer is stopped mid-cycle and leaves their clothes unwashed and a machine that won’t finish the task. The washing machine can stop mid-cycle for a variety of reasons, including problems in the drain system, or the power supply. In this post, we’ll examine the most common causes of this issue. We will also provide helpful solutions to fix your Haier washer and return to doing your laundry effortlessly.
Problem with Incoming Power
Make sure the power cord is not loose. In order to ensure uninterrupted electrical power, the cord must be securely connected.
Haier Washing Machine Control Board
A Haier control board for washing machines can supply voltage to nearly all of the components that power the washing machine. A faulty board can cause the washer to stop in the middle of a cycle. The board is able to be examined for signs of burnt or shorted components. After looking over the wiring diagram it is possible to use a multimeter to verify the power output terminals.
Haier Washing Machine Door Lock Motor and Switch Assembly
The door lock secures the Haier washer door during operation. Once the door to the washer is closed, the washer can begin to operate. The door switch will stop the washer from operating when the door of the washer isn’t shut. If the lock on the door is damaged, the washer might stop mid-cycle. The door lock can fail mechanically or electrically. Check the door lock for damage. Replace the door lock if broken or doesn’t latch correctly. To identify if the door lock is failing electrically, check the diagram on your washer’s website and use a multimeter check each of the switches on the door lock for continuity. Replace the switch if there is no continuity.
Haier Washing Machine Lid Switch
The lid switch assembly stops the Haier washer from spinning once the lid is open. If the lid switch assembly fails, the washer may stop mid-cycle. To determine if the lid switch assembly is defective, use the multimeter to examine each of the lid switches for continuity. If a lid switch is found to not have continuity, replace it.
The Haier is not getting enough water.
Check that the cold water is flowing into the tub. If the cold water supply is slow or not entering the tub in any way It is possible that the Haier washer will stop ahead of the rinse cycle while waiting for the tub to fill up. It could be because of an inlet valve that is blocked or a partially closed main valve for water supply, or low water pressure from your home.
Haier Washing Machine Water Inlet Valve
The Haier water intake valve is opened during the rinse cycle to allow water to enter the wash tub. The washer waits for water to enter the wash tub if the valve that opens water is damaged. Then it will shut down halfway through the cycle. Multimeters can be used to check for continuity in the valve for water inlet. If the valve for water inlet is not in good working order then replace it.
Haier Washing Machine Drain pump
A Haier washing machine drain pump helps in the removal of water from the tub through forcing the water to go through a drain pipe to a laundry tub or drain pipe. Because water is drained from the tub several times during a wash cycle A malfunctioning drain pump could stop the washer in mid-cycle. Verify the drain pump for obstructions if you find water in your tub even after the washing machine has stopped. It is also possible to use a multimeter to test the drain pump to determine if it is in electrical continuity. check if it is functioning or not.
Haier Washing Machine Main Control Board
The Haier main control board could be inoperable. But, the control board itself isn’t always responsible for this problem. Before replacing the control board that is in charge, make sure to check the other parts that are typically damaged.
Haier Washing machine timer
The timer might be defective. It is often misdiagnosed. Before replacing the timer, first check all of the more often defective parts. Check the wiring diagram of the washer in order to identify whether it is damaged. Then, employ a multimeter in continuity checking.
A Haier washing-machine that fails halfway through the cycle could be an annoyance. However, there are a variety of solutions to resolve the issue. You can fix the problem by following the instructions in this article. Before you tackle any repairs, unplug the device. It’s best to seek professional help if you are unsure of your skills to fix the issue. You can repair your Haier washer with some patience, understanding and skill. This will ensure that your clothes are clean and fresh each time.