An GE washing machine that stops mid-cycle can be an extremely frustrating and confusing problem to deal with. It is frustrating when you have to start the process again as well as lead to costly repairs if the problem continues. However, many of the reasons for a washing machine from GE stopping mid-cycle can be easily fixed by the home owner. In this article, we will review the typical causes for a GE washing machine that stops mid-cycle. We will also provide step-by-step instructions for fixing the problem. We’ll assist you in resetting the timer as well as check the lock on your door to ensure that your GE washer functions normally again. We can help you fix your GE washer if it ceases to work during the middle of the cycle. Incoming Power Issue Be sure the power cord is not loose. To ensure constant electrical supply to your GE washer, it has to be properly plugged in.
Washing Machine Control Board: The GE washing machines control board supplies voltage to nearly all electrical components. If the board is damaged, the washer might stop at the middle of the cycle. The board can be inspected for signs of burned or shorted components. After reading the wiring diagram you can test the multimeter to examine the power output terminals.
Washing Machine Door Lock Motor and Switch Assembly: The GE door lock locks the door to the washer during operation. After the GE door for the washer is shut the washer will begin operating. If the GE washer door isn’t latched shut the door switch will stop the GE washer from operating. The machine may stop at any point in the cycle if the door lock fails. Door locks can fail mechanically or electronically. Verify the door lock for any damage. If the door lock is damaged or fails to latch properly, replace it.
Washing Machine Lid Switch Assembly: The lid switch assembly keeps the washing machine from spinning while the lid is open. If the lid switch assembly is defective, the washer can stop in mid-cycle. To check if the lid assembly is defective, use the multimeter to examine each of the lid switches for continuity. Replace any lid switch that has no continuity. A lack of water Ensure that the cold water is circulating into the tub. If the flow of cold water is slow or not getting into the tub in any way, the GE washer will shut off ahead of the rinse, waiting for the tub to be filled. This could be due a blocked water inlet valve or a partially closed main water supply valve or low water pressure from your home.
Washing Machine Water Inlet Valve: The water inlet valve is open during the rinse cycle to allow water to flow into the tub for washing. The washer is waiting for water to enter it and, if the valve fails the washer will stop halfway through the process. To find out if the water inlet valve is defective, use an instrument to check it for continuity. If the valve to the water’s inlet isn’t functioning then replace it.
Washing Machine Drain Pump: A GE drain pump for washing machines assists in removing water from the tub by forcing the water to go through a drain hose to a drain or laundry tub pipe. A damaged drain pump may cause the washer to stop mid-cycle since water can be taken away multiple times from the tub throughout the wash cycle. It is recommended to inspect the drain pump for any obstructions if there’s still water in your tub after your washer has stopped. To check if the drain pump is working in a proper manner, use an instrument called a multimeter.
Washing Machine Main Control Board: The main control board may be defective. It’s not a common problem. Before you replace the main control board make sure to inspect all other parts that are more often malfunctioning.
Washing Machine Timer: The timer may be defective. When diagnosing the timer, prior to replacing the timer, look over all of the typically defective components. To determine if the timer is malfunctioning, refer to the wiring diagram for your washer. You can also make use of a multimeter in order to test the continuity of the timer.
In the end the conclusion is that it is true that a GE washer that stops mid-cycle could be an issue that is frustrating However, it’s quite simple to resolve. It is possible to fix common issues like clogged filtering or damaged door locks. Before you attempt any repair or maintenance, disconnect your washer. If in doubt you are unsure, refer to the manual or consult an expert. With a little patience and a bit of time it is possible to have your GE washing machine running smoothly once more, avoiding the hassle of having to restart the machine and repair costs. Remember also to keep an eye on your machine and examine if there is a problem and take the necessary actions.