It can be frustrating and confusing to have your Electrolux washer stop in mid-cycle. It’s not just annoying to to restart the machine and then restart it again, but it could also cost you money if the issue persists and requires a professional repair.
Homeowners can resolve many reasons why Electrolux washing machines stops mid-cycle. In this article, we’ll examine the common reasons for a Electrolux washing machine stopping mid-cycle and offer step-by step instructions for fixing the problem. We will help you troubleshoot the timer and check the lock on your door to ensure your Electrolux washing machine is working as it should. We can help you fix your Electrolux washer when it fails to operate in the middle of the cycle.
Incoming Power Problem
Check that the power cord isn’t loose. It must be connected securely to ensure constant electric power to the Electrolux washer.
Washing Machine Control Board
A Electrolux washing machine control board provides electricity to most electrical parts. If the control board is damaged, the washing machine might stop in mid-cycle. The board can be inspected for signs of burned or shorted components. After reviewing the wiring diagram, you can use a multimeter on the board to check the power output connections.
Door lock for the washing machine switch and motor
This Electrolux door lock is used to secure the door to the washer while in operation. When the Electrolux door for the washer is shut the washer is able to begin operating. The Electrolux washer won’t start working if the Electrolux door isn’t shut. If the door lock is broken, the washer may stop mid-cycle. Door locks can either fail electronically or mechanically.
Examine the door lock to see if it is damaged
Replace the door lock if the lock is damaged or fails to latch properly. Washing machine lid switch assembly This stops the washer spinning when the lid is opened. If the lid switch assembly is defective, the washer can stop mid-cycle. A multimeter is a good tool to examine each lid switch for continuity. If the lid switch does not have continuity, then replace it.
Insufficient water supply
Be sure that the cold water supply is entering the tub. If the water supply isn’t flowing as fast or isn’t entering the tub in any way then the Electrolux washer will stop ahead of the rinse cycle while waiting for the tub to fill. This could be due to an obstruction in the water supply valve or a partially shut main water supply valve or low pressure water coming from your home.
Washing Machine Water Inlet Valve
The valve for water inlet is closed during the rinse process to allow water to flow into the tub for washing. The washer will wait for the water to flow through it before closing the valve. If the valve fails, it will stop halfway through the process. To identify if the water intake valve is not functioning, use a multimeter to test it for continuity. Replace the water inlet valve when it is not in continuity.
Washing Machine Drain Pump:
A Electrolux washing machine drain pump aids in removing the water from the tub through forcing the water through a drain pipe to an empty laundry tub or drain pipe. Because water can be draining from the tub many times throughout a wash cycle, a defective drain pump could cause the washing machine mid-cycle. It is important to examine the drain pump to find any obstructions, if there’s still water in the tub after the washer has stopped. You can also use a multimeter to test the drain pump for electrical continuity to confirm if it is functioning or not.
Washing Machine Main Control Board
The main control board could be damaged. However, the control board isn’t always responsible for this particular symptom. Before replacing the control board in the main take a look at all the parts that are more likely to fail.
Washing Machine Timer:
The timer might be damaged. If you suspect that the timer is defective, before replacing the timer, examine all the typically defective components. Look over the wiring diagram of the washer in order to identify if the washer is in a state of deficiency. You can then make use of a multimeter for continuity testing. In conclusion in the end, it is true that a Electrolux washer that stops mid-cycle could be a major issue however, it’s an easy fix.
Following the instructions in this post, you’ll be able to identify and fix common issues such as clogged filters, faulty door lock or incorrect timer settings. Before you start any maintenance or repairs, unplug the washer. If in doubt you are unsure, refer to the manual or seek out a professional. With just a patience and a bit of time it is possible to have your Electrolux washing machine working without issue, and avoid the hassle of having to restart the cycle and the expense of repairs. Be sure to keep an eye on your washing machine to find out whether there are any issues and take the appropriate steps.