A washing machine is an essential appliance that is used in all households. It helps us save time and energy through automation of washing clothes. A lot of people be faced with the problem that their washer stops mid-cycle. The result is dirty clothes as well as a machine that’s not able to finish the job. There are a variety of reasons a washer may be stopped mid-cycle, such as issues with the water drainage system, the power supply, or malfunctioning parts. In this post, we’ll explore some of the most commonly-cited causes for this problem and provide useful solutions to fix your Electrolux washer so that you can get back to doing the laundry you love with ease.
Incoming Power Problem with Incoming Power
Check that the power cord is secured. It must be plugged in tightly to ensure that there is constant electricity to the washer.
Electrolux Washing Machine Control Board
A Electrolux washing machine controlboard is the source of voltage for most of the washer’s electrical components. A defective board can cause the washing machine to stop in the middle of the cycle. The board can be checked for evidence of burnt or shorted components. After you have reviewed the wiring diagram then you can test the board with a multimeter on the board to test the power output terminals.
Electrolux Washing Machine Door Lock Motor and Switch Assembly
The door lock secures the Electrolux washer door closed during operation. Once the washer door is closed, the washer can begin operating. The door switch stops the washer from working when the door isn’t shut. The washer will stop at any point when the lock on the door fails. The door lock may malfunction either electrically or mechanically. Inspect the door lock to find any damage. If the lock is damaged or does not latch properly you should replace it. To determine if the door lock has failed electrically look up the diagram of your washer and use a multimeter to check each of the switch on the door lock to determine continuity. Replace the switch in the event that there is no continuity.
Electrolux Washing Machine Lid Switch
The lid switch assembly stops the Electrolux washer spinning when the lid is opened. If the lid switch assembly fails, the washer may stop mid-cycle. To determine if the lid switch assembly is damaged, use the multimeter to examine every lid switch for continuity. If the lid switch does not have continuity, you should replace it.
Insufficient water supply to Electrolux
Be sure the cold water is getting into the tub. The washer won’t start the rinse process if the cold water supply is slow or isn’t reaching the tub. It could be due to the water inlet valve being blocked or a partially closed main valve for water supply, or the water pressure is low at your home.
Electrolux Washing Machine Valve for Water Inlet
The Electrolux water intake valve opens in the course of the rinse to allow water to enter the wash tub. If the valve to open the water inlet fails, the washer will keep waiting for water to flow into the washer which will cause it to stop at the middle of the cycle. Multimeters can be used to determine the continuity of the water inlet valve. Replace the valve that is used for water inlet to ensure it has continuity.
Electrolux Washing Machine Pump to drain
The Electrolux washing machine drain pump helps to drain the tub water by forcing it through an drain tube or pipe to drain the water. A malfunctioning drain pump can cause the washer to stop in mid-cycle since water may be drained multiple times out of the tub throughout the wash cycle. Make sure the drain pump is free of obstructions if there is still water in your bathtub after the washer has stopped. For testing for electrical continuity using the multimeter. This will help determine if the pump works.
Electrolux Washing Machine Main Control Board
The Electrolux main control board could be defective. However, the control board itself is not always the cause of this issue. Before replacing the main control board make sure you check all the most frequently defective components.
Electrolux Washing Machine Timer
The timer could be damaged. The timer is frequently misdiagnosed–before replacing the timer, verify all of the typically defective parts. Check the wiring diagram of your washer to determine if the washer is defective. After that, make use of a multimeter for continuity checking.
In the end it is clear that a Electrolux washing machine that stops mid-cycle could be a frustrating event however, there are a variety of ways to troubleshoot and fix the issue. Following the steps laid out in this article, you’ll be able to pinpoint and solve the root reason for the problem that is causing the issue, whether it’s a blocked drain, malfunctioning motor, or an electrical issue. Be sure to unplug the machine and ensure that you take all the safety precautions prior to attempting any repairs. It is best to seek out professional assistance if you’re not sure of your abilities to repair the problem. With a bit of patience and know-how, you can fix your Electrolux washing machine back up and running at a high level, ensuring that your clothes will be clean and fresh every time.