An Speed Queen washing machine that stops mid-cycle can be an issue that is confusing and frustrating to address. Not only is it inconvenient to have to start the cycle, but it can also cost you a lot of money if the issue persists and requires professional repair. The homeowner can address a variety of reasons that a Speed Queen washer machine is stopped mid-cycle. We will discuss common reasons Speed Queen washing machines stop mid-cycle , and provide the steps to fix it. We’ll help you figure out the cause of the timer and examine the door lock to ensure your Speed Queen washer functions normally again. We can help you fix your Speed Queen washer when it ceases to function during the middle of the cycle. Incoming power problems Verify that the power cord has been tightened. In order to ensure continuous electrical power for your Speed Queen washer, it needs to be properly plugged in.
Washing Machine Control Board : A Speed Queen washing machines control board supplies electricity to most electronic components. If the control board is damaged, the washing machine may stop at mid-cycle. The control board can be checked for signs of burnt or damaged components. After looking over the wiring diagram you can test the multimeter on the board to verify the power output terminals.
Washing Door Lock Motor for Machine and Switch Assembly: The Speed Queen door lock is used to keep the door of the washer to keep it closed when it is in use. When the Speed Queen door to the washer has been closed, the washer can begin functioning. The Speed Queen washer won’t start functioning in the event that the Speed Queen door isn’t closed. The washer could stop in mid-cycle if the door lock fails. Door locks may fail electronically or mechanically. Verify the door lock for any damages. Replace the door lock if it is broken or doesn’t latch correctly.
Washing Machine Lid Switch Assembly: The lid switch assembly keeps the washer from spinning while the lid is open. The washer could stop mid-cycle when the lid switch assembly is damaged. A multimeter is a good tool to examine each lid switch for continuity. If a lid switch does not show continuity, replace it. A lack of water Be sure that the cold water supply is entering the tub. The Speed Queen washer will not initiate the rinse cycle if cold water supply is slow or does not reach the tub. This could be due the water inlet valve being blocked or a partially shut main valve for water supply or the water pressure is low at your home.
Washing Machine Water Inlet Valve: During the rinse cycle, the water inlet valve opens to allow water to get into the wash tub. The washer will wait for water to get in before closing the valve. If the valve fails, it will stop halfway through the process. To check if the inlet valve is not functioning, use an instrument to check it for continuity. Replace the water inlet valve If it doesn’t have continuity.
Washing machine drain pump: The Speed Queen washing-machine drain pump assists in draining the tub of water. It pushes the water through the drain tube or pipe that connects to a laundry tub. A defective drain pump could cause the washer to stop mid-cycle in the event that water is dumped multiple times out of the tub during the wash cycle. It is recommended to inspect the drain pump for obstructions if there is still water in the tub after washing has stopped. You may also utilize an instrument to check the drain pump to determine if it is in electrical continuity. check if the pump is able to function or not.
Washing Machine Main Control Board: The control board on the main board could be in a state of deficiency. However, the main control board is rarely at fault for this symptom. Before replacing the main control board , make sure that you inspect the other components that are often damaged.
Washing Machine Timer: The timer might be damaged. When diagnosing the timer, prior to replacing the timer, first check all of the more typically defective components. To find out if the timer’s defective, consult the wiring diagram on your washer, and make use of a multimeter in order to test the timer’s continuity.
A Speed Queen washing machine which is stopped mid-cycle may be frustrating, but it’s usually an easy solution. By following the guidelines in this post, you’ll be able troubleshoot and address common issues like clogged filters, defective door locks and improper timer settings. Before you attempt any repairs or maintenance, disconnect your washer. If you’re unsure you are unsure, refer to the manual or contact an expert. You can have your Speed Queen washer back in operation with a little patience and a little bit of patience. This will save the time of starting the cycle again, and will lower the cost of repairs. Monitor your machine to determine if there are any problems and take the appropriate steps.