There’s a good chance you’ve had the annoyance of an Blomber washing-machine that wouldn’t stop overflowing with water. It’s not just a waste of water and energy but may also cause damage to your floors as well as Blomber washer. We’ll go over common issues and give step-by-step directions for fixing a washer from Blomber that is constantly filled with water. No matter if you’re a skilled DIYer or a complete novice, you’ll discover the necessary information to get your Blomber washing machine back into running in good working order. Read on if you’re looking to repair the problem with your Blomber washer!
Water Inlet Valve
The Water Inlet Valve of your Blomber washing machines is used to fill the tub with hot, cold or warm water. The valve is operated using solenoids powered by electricity that are controlled by the electronic control board or timer and the water level control/water level selector switch, or pressure switch. If your Blomber washer continues to fill during a cycle the valve that allows water to enter could be at fault. To verify that the valve is in error Unplug the Blomber washer as soon as the symptom is observed. The water inlet valve could be damaged if the washer is filling continuously. The issue could be within the electrical circuit controlling the valve. How to test the valve for water inlet in a Blomber washing machine using a multi-meter:
- Like all tests, be sure to have turned off the power source to the Blomber appliance prior to starting. It will be conducting electrical tests on the components.
- Find and remove your water intake valve. It’s usually located right behind the hose connectors and you’ll need to take off the back panel to get it in place.
- Visually inspect the valve to see if there are any indications of wear. You will need to replace the entire valve if it has screens.
- Make use of a multimeter to contact the terminals of the valve’s ports with Rx1. You should get a different reading for each model. Check the manual to learn what measurement you should receive.
- If your valve is damaged or your tests do not meet the recommended results, you will need Blomber replacement water inlet valve.
Level switch pressure switch & air dome tube
The water level switch, which is activated by pressure from the water, is used to control the level of the water in the tub. The control panel is likely to have this part. It will be connected to the tub with the use of a hose or air dome tube. On Blomber washers with an electronic control this switch can be located at an area called the sump that is beneath the tub. When the water is filled into the tub it will compress the air inside the tube and push against a diaphragm inside the switch. The valve that opens the water will be controlled by the switch, which will shut off the valve at the correct level of water. The washer could overfill in the event that the tube is damaged or leaky. If the switch is not working properly, it can result in the machine overfilling. How to check the level of water in aBlomber washer machine:
- Because you’ll be working with electrical components, be sure you have removed your washer from its power source prior to starting.
- For the removal and location of the water-level switch and air dome tube from the inside of your Blomber washer, open the cabinet. Once removed, plug one end of the air dome tube immerse it in water and blow through the other end. A hose that is not damaged will not contain any bubbles that come out of it.
- Inspect the hose and the valve for any signs of wear, cracks, or damage.
- If any issues are found in the process of performing the checks mentioned above, you may need a Blomber replacement water level switch.
A washing machine from Blomber that isn’t filled with water can cause expensive and annoying issues. By understanding the most common causes for this problem and taking proper steps to correct it, you’ll be able to save time and money. This article will assist you to resolve the issue with the problem with your Blomber washer, regardless whether the issue is with the water level switch or the valve for inlet. Before you tackle any repairs It’s recommended to read the manual for your washer. It’ll provide specific directions for troubleshooting as well as safety precautions. If you’re not sure if the issue can be resolved by yourself, it’s recommended to call a professional to do repairs. Overall, with a some knowledge and the right strategy, you can fix a Blomber washer that isn’t filling with water and return to washing your laundry without difficulty.