There’s a good chance you’ve had the annoyance of an Miele washing machine that kept overflowing with water. It’s not just a waste of the water and energy it can also cause damage to your floors and even your Miele washing machine itself. In this post, we’ll take a look at the most common causes of this issue and give step-by step instructions on fixing a Miele washing machine which isn’t able to stop filling with water. There’s all the necessary information to fix the issue with your Miele washer, no matter whether you’re a professional or novice. If you’re looking to repair that nagging Miele washer, then keep reading!
Water Inlet valve:
The Water Inlet Valve located on the inside of your Miele washing machine is used to supply the tub with hot, cold, warm, or cold water for wash and rinse cycles. The solenoids on the electrical circuits control the valve. They are controlled by the electronic control board, the timer, the water level control/water selector switch or the pressure switch. If your Miele washer continues to fill during a cycle it is possible that the valve for water inlet could be in error. If the Miele washer continues to fill then the water inlet valve may be the cause. If the Miele washer continues to fill, the water inlet valve is damaged. If the washer does not fill it is caused by the electrical circuit that regulates the valve. How to test the valve for water inlet in a Miele washing machine using a multi-meter:
1. Like all tests, make sure you have turned off the power supply to your Miele appliance prior to starting. It will be working with electrical components.
2. Find and remove your water inlet valve. It’s located just behind the connections for the hose. To reach it, you’ll need the rear panel to be removed.
3. Check the valve visually for signs of wear or damage. The valve is fitted with screens within it. Check these screens for any signs of debris, be careful as these screens aren’t replaceable and if damaged, it is necessary to replace the entire valve.
4. Make use of a multimeter to contact the valve’s terminals ports by using Rx1. You should get a different reading for every model. Look up your manual to find out what measurement you should receive.
5. You’ll require a replacement Miele water inlet valve if the valve is damaged or the test results are not consistent with the recommendations.
Water level switch & pressure switch & air dome tube:
The water level switch, which is activated by the pressure of water, is used to regulate the level of water within the tub. The control panel will usually include this component. It will be connected to the tub with a hose, or air dome tube. The switch can be found below the tub in Miele washers and comes with an electronic control. The water will then fill the tub and then compress the air inside it, pushing against the diaphragm. The switch will control the water inlet valve , and close the valve at the appropriate level of water. The washer may overfill if the tube damaged or leaky. If the switch is damaged, it can cause the machine to fill too high.
How to test the water level switch in the Miele washing machine
1. Because you will be handling electrical components, ensure that you have disconnected the washer from the power source before beginning.
2. You must open your Miele washer’s cabinet in order to locate and then remove the switch for water level as well as the air dome tube. When the air dome tube has been removed, put one end into the tank, and blow it into the other. A hose that is not damaged will not have any bubbles coming out of it.
3. Examine the hose and valve for wear, cracks, or damage.
4. If you find any problems when performing the checks above, you may need Miele replacement water switch for the level. A washing machine from Miele that doesn’t fill up with water could cause frustration and cost. It is possible to save time and money by discovering the reasons and then taking the required steps to fix the problem. It doesn’t matter if the issue is a problem with the water level switch or a blocked valve for the inlet
The solutions described in this article will help you to get the Miele washing machine to work properly. It’s always recommended to refer to your washer’s user manual to learn specific troubleshooting procedures and safety measures prior to undertaking any repairs. If you’re not sure if the problem can be fixed by yourself, it’s recommended to call experts to handle the repairs. With just a bit of knowledge and the right method, you can fix Miele washers that won’t fill up with water. And, then, you can go back to doing laundry.